Ademco - 269R & 270R Hold-Up Switch

12 02 Switch AND SETUP GUIDE INFORMATION 269R 270R Holdup Switch Figure 1 is a finger operated for activating the holdup signal at the control and or any security application The 269R adds a protective steel The Holdup Switch is typically mounted under a counter inconspicuous operation The device comes standard as a type switch that is easily converted to a non latching the switch is used as a latching type switch the supplied key is used to reset the device Additional reset keys may obtained separately by ordering ADEMCO part number Ademco controls program the unit like any other zone to the control installation and setup guide Enter zone TYPE TYPE other manufacture controls refer for specific programming instructions to the steps and figures that follow for typical installation If required convert the latching to a non latching device as shown in figure 2 when prompted controls Run the wiring from the control panel to the device the opening in the case back as shown in Figure 3 Wire the device for a normally closed or a normally open with no EOL resistor or for a normally closed or a open loop with an EOL resistor as shown in 4 Where Form C wiring is required providing full of the loop refer to figure 5 Secure the cover to the case with two screws No 6 x 7 8 shown in figure 6 Be sure to use the correct holes The opposite these are used to secure the device to the To prevent damage to the case do not tighten the cover screws Peel the backing from the double stick tape strips on the of the device as shown in Figure 7 and position the in its mounting location The double stick tape is provided to hold the assembly in place while the pilot holes The device must be mounted with the screws supplied Using the case as a drill template drill a 1 16 diameter hole at the two case mounting holes Figure 1 Secure the assembled case with the protective cover if to the counter with two screws No 6 x 1 3 4 Figure 8 KEY SUPPLIED HOLE 2 6x7 8 ONLY 1 2 6X1 3 4 POINT CONVERT TO MOMENTARY NO LATCHING SWITCH REMOVE THE TRIGGER ASSEMBLY FROM THE USING A PAIR OF CUTTERS CUT THE TRIGGER LATCH THE POINT THE ARROW IS STAMPED ON THE CASE THE WIRE THROUGH THE WIRE ENTRY HOLE 3MM 125 INCH OFF THE WIRE ENDS 2 3 AS SHOWN FOR NORMALLY CLOSED WITH NO EOL AS SHOWN FOR NORMALLY OPEN WITH NO EOL AS SHOWN FOR NORMALLY CLOSED WITH AN EOL AS SHOWN FOR NORMALLY OPEN WITH AN EOL RESISTOR THAT THE EOL IS NOT USED A NORMALLY OPEN LOOP 4 C PROVIDES SUPERVISION THE LOOP 2 6X7 8 PANEL TERMINALS 5 HOLE COVER TO CASE USING 6x7 8 SCREWS SUPPLIED PREVENT DAMAGE TO THE CASE NOT OVER TIGHTEN COVER SCREWS THE COVER SCREWS ARE NOTICEABLY THAN THE MOUNTING SCREWS 6 COVER ONLY BACKING FROM DOUBLE STICK TAPE DOUBLE STICK TAPE IS PROVIDED TO TEMPORARILY THE ASSEMBLY IN PLACE WHILE DRILLING THE HOLES THE DEVICE MUST BE PERMANENTLY WITH THE SCREWS SUPPLIED DEVICE MUST PERMANENTLY WITH THE SUPPLIED 2 6X1 3 4 SWITCH SHOWN MOUNTED TYPICAL UNDER COUNTER APPLICATION 7 8 Key x 3 1 2 H x 1 1 4 D x 89mm x 32mm Amp 30 VDC MAX Observe contact rating limitations not use to switch Line Voltage AC current to 140 cid 131 F to 60 cid 131 C 636 Holdup alarm units and systems Part Number K4563 to order separately THE INSTALLER maintenance and inspection at least annually by the installer and frequent testing by the user are to continuous satisfactory operation of any alarm system installer should assume the responsibility of developing and offering a regular maintenance program the user as well as acquainting the user with the proper operation and limitations of the alarm system its component parts Recommendations must be included for a specific program of frequent testing at weekly to insure the system operation at all times LIMITED WARRANTY Device Manufacturing Company a Division of Pittway Corporation and its divisions subsidiaries and affiliates Seller 165 Way Syosset New York 11791 warrants its products to be in conformance with its own plans and specifications and to be free defects in materials and workmanship under normal use and service for 24 months from the date stamp control on the product or products not having an ADEMCO date stamp for 12 months from date of original purchase unless the installation instructions or sets forth a shorter period in which case the shorter period shall apply Seller obligation shall be limited to repairing or at its option free of charge for materials or labor any product which is proved not in compliance with Seller specifications proves defective in materials or workmanship under normal use and service Seller shall have no obligation under this Limited or otherwise if the product is altered or improperly repaired or serviced by anyone other than ADEMCO factory service For service return product transportation prepaid to ADEMCO Factory Service 165 Eileen Way Syosset New York 11791 ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF IN NO CASE SHALL SELLER BE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER EXPRESS OR IMPLIED OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR IS CAUSED BY THE SELLER OWN NEGLIGENCE OR FAULT does not represent that the products it sells may not be compromised or circumvented that the products will prevent any injury or property loss by burglary robbery fire or otherwise or that the products will in all cases provide adequate warning or Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or events occurring without providing an alarm but it is not insurance or a guarantee that such will not occur or that there will be no injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER MAXIMUM LIABILITY SHALL NOT IN CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE AGAINST SELLER This warranty replaces any previous warranties and is the only warranty made by Seller on this