Ademco - 5849 Wireless Glass Break Detector

Several of you have written us to ask that we reconsider this decision We have Tech Man Subscriber apologizes for any misunderstanding that has arisen due to our recent to have our technical information removed from the Tech Man web site You appreciate that one of our key concerns is to provide installing security dealers with and accurate information on our products and we were concerned about the data to the Tech Man web site For obvious reasons we also do not wish unauthorized to have access to information on installing and configuring ADEMCO These concerns were what prompted us to ask Tech Man to stop posting installation instructions and user manuals will not require Tech Man to remove the ADEMCO data ADEMCO however is responsible for the operation and maintenance of this site thus we cannot guarantee timeliness or accuracy of the information posted on the Tech Man web site data about our products You may request a PIN number for access to the Technical Support web site and FAXBACK system you need assistance on troubleshooting or if you have other technical questions our products not addressed in the information posted at our web site please contact Technical Support at 800 645 7492 ADEMCO web site is located at www ademco com and contains accurate you for understanding Lustig THE INSTALLER maintenance and inspection at least annually by the installer and frequent testing by the are vital to continuous satisfactory operation of any alarm system installer should assume the responsibility of developing and offering a regular maintenance to the user as well as acquainting the user with the proper operation and limitations of the system and its component parts Recommendations must be included for a specific of frequent testing at least weekly to insure the system operation at all times TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER CONTROL WITH WHICH THIS IS USED FOR DETAILS REGARDING LIMITATIONS OF THE ENTIRE ALARM SYSTEM LIMITED WARRANTY Device Manufacturing Company a Division of Pittway Corporation and its divisions and affiliates Seller 165 Eileen Way Syosset New York 11791 warrants its to be in conformance with its own plans and specifications and to be free from defects materials and workmanship under normal use and service for 24 months from the date stamp on the product or for products not having an Ademco date stamp for 12 months from of original purchase unless the installation instructions or catalog sets forth a shorter period which case the shorter period shall apply Seller obligation shall be limited to repairing or at its option free of charge for materials or labor any product which is proved not in with Seller specifications or proves defective in materials or workmanship under use and service Seller shall have no obligation under this Limited Warranty or oth if the product is altered or improperly repaired or serviced by anyone other than Ademco service For warranty service return product transportation prepaid to Ademco Factory 165 Eileen Way Syosset New York 11791 ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FOR A PARTICULAR PURPOSE OR OTHERWISE WHICH EXTEND BEYOND DESCRIPTION ON THE FACE HEREOF IN NO CASE SHALL SELLER BE LIABLE TO FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BY SELLER OWN NEGLIGENCE OR FAULT does not represent that the products it sells may not be compromised or circumvented the products will prevent any personal injury or property loss by burglary robbery fire or or that the products will in all cases provide adequate warning or protection understands that a properly installed and maintained alarm may only reduce the risk a burglary robbery fire or other events occurring without providing an alarm but it is not in or a guarantee that such will not occur or that there will be no personal injury or loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE AGAINST SELLER This warranty replaces any previous warranties and is the only made by Seller on this product No increase or alteration written or verbal of the of this Limited Warranty is authorized Eileen Way Syosset New York 11791 1997 PITTWAY CORPORATION 10 97 INSTRUCTIONS 10 97 5849 BREAK Set the system ready for learning the serial number as described the control instructions The 5849 be programmed as input Type 3 and Loop 1 Use a sound simulator such as the or equivalent to activate the sound channel Both yellow red LEDs should glow to indicate an Proceed with the learning procedure as in the control instructions Return the Shock Sensitivity Fine Pot to MIN position temporarily Considerations preferred location for the detector in to the glass to be protected is Along the same wall As close to the glass as possible but no than 20 feet along the wall from the glass Room acoustics and wall will affect the range It is very that the detector range be using proper test procedures Without intervening partitions etc that block transfer of shock or sound see Limitations the location could be on a wall abuts to the wall with the glass with all of other conditions still applicable window dressing is present it will absorb energy from breaking glass In such the detector should be mounted the protected glass and the window sources of ambient vibration or sound as air conditioners fans blowers or doorbells mounting the 5849 permanently Go No Go tests see control in to verify adequate signal strength reorient or relocate the 5849 if necessary the unit cover insert the blade of a screwdriver in the slot at one end of the INFORMATION Glass Break Detector Transmitter can the breakage of glass windows and or while wall mounted near the glass un surveillance and transmit a wireless to a receiver connected to the system panel This dual technology device both sound and shock waves as with glass breakage The glass can Ordinary Plate Tempered Wired Plate Laminated type both forms of energy must occur at the time for a valid alarm condition to be by the device the likelihood of false indications is kept to a minimum The that monitors sound waves is turned only when a shock signal is detected both channels are triggered an alarm is transmitted to the control indicators on the unit permit local ad and monitoring When a shock is the yellow SHOCK LED glows both shock and sound are detected LED and red ALARM LED will both detector is designed for continuous Separate alarm and cover tamper permit 24 hour monitoring THE TRANSMITTER ID 5849 has its own unique identification permanently assigned during manu It is not necessary to program the ID during installation Instead the unit is required to learn the ID at some point prior to its usage the alarm system control unit installation instructions general information on the learning but the information given herein specifically to the 5849 two 3V batteries refer to the section in the battery as shown in the diagram polarity Turn the Shock Sensitivity Fine Pot to maximum clockwise position The LED will glow steadily and mount the base in the selected Screws and plastic anchors are pro for a typical installation but any two fasteners may be used that secure base firmly to the mounting surface