Ademco - 5869 Wireless Hold Up Transmitter

AND SETUP GUIDE 2 01 Switch Transmitter INFORMATION 5869 Holdup Switch Transmitter is a finger operated transmitting device It is typically mounted under a or money draw for inconspicuous operation When transmitter is activated it emits a RF signal The system control panel sends a burglary alarm to the station when a RF signal is received from an Holdup Switch Transmitter activated the 5869 Holdup Switch Transmitter emits RF signal that can only be reset by the reset key The also incorporate tamper switches that are activated the cover is removed or if the unit is forcibly removed its installation location 5869 Holdup Switch Transmitter has a permanent number assigned during manufacture used for the 5869 with the security system control panel enroll the 5869 with the security system control panel to the Security System Control Panel Installation and Guide the 5869 under a counter or money drawer for easy by the cashier Refer to the steps and figures that for typical mounting instructions mounting the 5869 permanently perform Go No Go to verify adequate transmitter signal strength at desired location refer to the Security System Control Installation and Setup Guide Remove two screws Figure 1 securing the cover to the case The holes located in the opposite corner to the that secure the cover to the case provide a for securing the transmitter to the counter or Using the case as a drill template position the case in desired location Drill a 1 16 inch pilot hole at the breakaway tamper hole and the two case mounting holes Figure Attach the case to the counter or money drawer using No 6 x fastener supplied at the breakaway release the battery see BATTERY INSTALLATION Secure the cover to the case with the two screws in step 1 Secure the assembled case to the counter or drawer the two No 6 x 2 fasteners supplied Figure 1 Holdup Switch Transmitter as a 24 hour silent zone type Refer to the System Control Panel Installation and Setup for programming instructions During programming of the control panel the 5869 Switch Transmitter should be treated as RF supervised RF Type The 5869 is one closed input loop zone loop 1 INSTALLATION REPLACEMENT Remove and retain screws securing the 5869 cover Observing correct polarity insert the battery into the holder CAUTION of fire explosion and burns Do not recharge disas heat above 100 or incinerate Dispose of used promptly and properly Keep away from children Use care not to bend the antenna while attempting install battery Re install screws to secure cover and or assembly to Figure 1 x 5 15 16 H x 1 3 16 D x 150mm x 30mm Lithium ADEMCO 466 Duracell Panasonic CR123A Sanyo CR123A CR123A or equivalent HOLE BOARD REMOVED CLARITY ONLY DO NOT CIRCUIT BOARD INSTALLATION 2 6X1 2 2 6X2 HOLE 1 TAB TAMPER SWITCH VIEW BOARD 2 THE INSTALLER maintenance and inspection at least annually by the installer and frequent testing by user are vital to continuous satisfactory operation of any alarm system installer should assume the responsibility of developing and offering a regular program to the user as well as acquainting the user with the proper operation limitations of the alarm system and its component parts Recommendations must be for a specific program of frequent testing at least weekly to insure the system at all times LIMITED WARRANTY Device Manufacturing Company a Division of Pittway Corporation and its divisions subsidiaries and affiliates 165 Eileen Way Syosset New York 11791 warrants its products to be in conformance with its own plans specifications and to be free from defects in materials and workmanship under normal use and service for 24 from the date stamp control on the product or for products not having an ADEMCO date stamp for 12 months date of original purchase unless the installation instructions or catalog sets forth a shorter period in which case the period shall apply Seller obligation shall be limited to repairing or replacing at its option free of charge for or labor any product which is proved not in compliance with Seller specifications or proves defective in or workmanship under normal use and service Seller shall have no obligation under this Limited Warranty or if the product is altered or improperly repaired or serviced by anyone other than ADEMCO factory service warranty service return product transportation prepaid to ADEMCO Factory Service 165 Eileen Way Syosset York 11791 ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PURPOSE OR OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER OWN OR FAULT does not represent that the products it sells may not be compromised or circumvented that the products will any personal injury or property loss by burglary robbery fire or otherwise or that the products will in all cases adequate warning or protection Customer understands that a properly installed and maintained alarm may only the risk of a burglary robbery fire or other events occurring without providing an alarm but it is not insurance or guarantee that such will not occur or that there will be no personal injury or property loss as a result SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER MAXIMUM LIABILITY SHALL IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE EXCLUSIVE REMEDY AGAINST SELLER This warranty replaces any previous warranties and is the only made by Seller on this product No increase or alteration written or verbal of the obligations of this Limited is authorized Eileen Way Syosset New York 11791 2001 PITTWAY CORPORATION 2 01