Ademco - 5878 Installation Manual

AND SETUP GUIDE 6 06 Rev A Wall Transmitter INFORMATION 5878 is a six button eight loop wall mountable wireless It is intended for use only with wireless alarm that support 5800 series receivers Individual buttons the transmitter may be programmed for any zone response are typically used for arming or for home automation Optional function buttons are provided with the not use for system disarming in an area that security device supports both Standard and High Security modes The latter sends rolling code encrypted to the RF receiver device must be used with a receiver or control supports high security mode i e 5881EN 5883 or 6160RF receiver or a LYNXR Series panel Revision 13.1 or higher if you intend use it in high security mode 5878 is powered by one replaceable lithium battery de to provide up to four years of life For battery see Replacing the Battery 1 3 1 4 2 3 1 2 1 1 2 2 WALL TRANSMITTER SERIAL 2 LOOP 1 AWAY 4 BUTTON 4 3 4 BUTTONS 1 5878 Button Designations 5878 is assigned two unique serial numbers during and each button or button combination on the also has a distinct loop number refer to Figure 1 that be programmed into the control panel during installation each button or button combination to one of eight zones and designate the Input Type as BR Button RF you are enrolling the 5878 locally with an RF refer to the keypad Installation for programming instructions When prompted enter the serial number either by and releasing the button or buttons that you are twice wait about 5 seconds between button Manually through the keypad 1 To activate the transmitter the 5878 buttons must be and held for at least one half second Serial 2 is one 1 digit higher than serial 1 which is on the rear of the transmitter 4 Setup of the Loop 4 buttons must be enrolled in the control even they will not be used If one or both of the loops is not being program it as Zone Type 23 No Alarm Response assign it to the desired zone type Exit Programming Mode after programming is complete For complete details on how to program the transmitter number at the control panel see the control unit instructions a 5878 to a User most control panels if the wall transmitter is used for functions you must assign it to a user in order for it to This is accomplished through User Code programming the control panel See the control panel Installation and Guide for specific instructions on programming User you are programming arming functions on both serial each serial number must be assigned to a separate STANDARD OR HIGH SECURITY MODE use with LYNXR Series controls earlier than 13.1 the Standard Mode must be select Standard Mode simultaneously press and hold the 1 and 2 buttons for three seconds select High Security Mode simultaneously press and hold AWAY 1 and 2 buttons for three seconds LED flashes green when transmitting in Standard Mode red when transmitting in High Security Mode HIGH SECURITY MODE ensure proper functionality the 5878 must be to the security system To sync the transmitter with the receiver simultaneously and hold the AWAY STAY 1 and 2 buttons until the beeps see Figure 1 For LYNXR Series controls to step 4 The LYNXR Series panels will confirm the synchronization sounding two beeps To sync the device in High Security Mode press either the STAY 1 or 2 button ONCE until the panel beeps receipt To sync the second serial number of the wireless key with the simultaneously press and hold the 1 2 3 and 4 until the panel beeps For LYNXR Series controls to step 6 To sync the device in High Security Mode press the 3 or 4 ONCE and hold until the panel beeps indicating If no beep is heard exit Go No Go mode and repeat 1 5 Exit Go No Go mode by entering user code 1 OFF Test mode After selecting High Security mode put the system in Go No TWO RECEIVERS IN HIGH SECURITY MODE the control supports two receivers and you plan to use them the high security mode perform the following Enroll the transmitters into the receivers one at a time by Receiver 2 and enrolling as described in High Security Mode above Disconnect Receiver 1 reconnect Receiver 2 and repeat enrollment procedure This process ensures proper High operation with both receivers disable receivers supervisory while enrolling to prevent them from going when disconnected After enrolling the supervisory zones THE BATTERY LED will not flash during transmission if the battery is To replace the battery perform the following steps Slide out the battery tray located at the bottom of the 5878 Carefully remove the battery Press and hold any button for at least one second Insert a new battery in the tray as shown in Figure 2 end must face up Use Maxell CR2032 DL 20325 or Varta CR2032 lithium battery only Slide the battery back into the 5878 Press any button and verify that the LED flashes THE 5878 5878 can be mounted directly to a wall or other surface two sided double stick tape or by using the provided plate the 5878 using the back plate as follows Mount the back plate to a sturdy wall using self tapping supplied anchors for drywall are not supplied or two adhesive tape Install the 5878 onto the backplate and slide it downward the locking device engages To remove the 5878 from the back plate release the locking by pushing it towards the wall and then care sliding the 5878 upward until it is released WALL 2 PLATE W A installation will result in damage the battery SIDE FACE UP OR 3 Installing the 5878 2 Battery Replacement Dimensions in 114.3mm x 2.75 in 69.85mm x 5 in 12.7mm CR2032 Duracell DL 20325 or Varta CR2032 WARRANTY INFORMATION AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM REFER TO THE INSTALLATION FOR THE RECEIVER CONTROL WITH WHICH THIS DEVICE IS USED AND INDUSTRY CANADA STATEMENT DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS210 OF INDUSTRY CANADA OPERATION IS SUBJECT TO THE FOLLOWING TWO 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION USER SHALL NOT MAKE ANY CHANGES OR MODIFICATIONS TO THE EQUIPMENT UNLESS AUTHORIZED BY THE INSTALLATION AND SETUP GUIDE THE USER GUIDE 6 06 Rev A Brookprinter Place Poway CA 92064 2006 Honeywell International Inc