Ademco - 5890PI Passive Infrared Motion Detector-Transmitter

Several of you have written us to ask that we reconsider this decision We have Tech Man Subscriber apologizes for any misunderstanding that has arisen due to our recent to have our technical information removed from the Tech Man web site You appreciate that one of our key concerns is to provide installing security dealers with and accurate information on our products and we were concerned about the data to the Tech Man web site For obvious reasons we also do not wish unauthorized to have access to information on installing and configuring ADEMCO These concerns were what prompted us to ask Tech Man to stop posting installation instructions and user manuals will not require Tech Man to remove the ADEMCO data ADEMCO however is responsible for the operation and maintenance of this site thus we cannot guarantee timeliness or accuracy of the information posted on the Tech Man web site data about our products You may request a PIN number for access to the Technical Support web site and FAXBACK system you need assistance on troubleshooting or if you have other technical questions our products not addressed in the information posted at our web site please contact Technical Support at 800 645 7492 ADEMCO web site is located at www ademco com and contains accurate you for understanding Lustig INSTRUCTIONS use with QED control panels ONLY INFORMATION 5890PI Passive Infrared Motion is a battery operated device intended for use as part of a 5800 series wireless alarm system for use in commercial and installations the 5890PI is a wall unit with a standard lens that wide angle protection up to a range 35 ft 10.6m For best coverage mount the so that the likely direction of motion is across the pattern installed per the guidelines the Split Optics technology in the 5890PI reasonable false alarm protection pets and other animals up to 40 lbs document provides for the 5890PI but the installer be familiar with the installation for the QED 5800 Wireless System with which the 5890PI is to be used Split Zone Optics provides pet immunity animals up to 40 lbs Wireless operation for fast installation Dual element pyro electric sensor provides protection while minimizing false Alternate polarity pulse count option offers stability in adverse environments Provision to turn LED on while Walk LED is turned off after testing Tamper protected cover unit transmits if cover is removed Wall or corner mounting options DESCRIPTION System Uses efficiently designed lenses with Split Zone Optics Transmitter The built in link to the alarm system and can send alarm supervisory and battery status QED The transmitter is not used detection purposes Each detector has a ID code permanently assigned at the You must enroll this ID into the QED system at the time of installation allows each detector used in the system be uniquely identified You must program QED control to enroll the 5890PI as an type unit i e supervised RF conserve battery life during normal no more than one transmission will occur within a 3 minute period is no such time restriction in Test Polarity Pulse Count Two detection response modes provided Instant response Pulse Count and Alternate Polarity Pulse Count Count ON With Pulse Count OFF detected change in infrared energy will an immediate alarm signal This is recommended when the detector is to monitor a narrow hallway where is provided by only a single zone the Pulse Count ON mode when the is installed in areas where periodic in infrared energy levels are normal example where forced air heating ducts present In this mode at least two in infrared energy must be detected a short period before an alarm will be Note For pet Pulse Count ON Immune ft x 45 ft x 13.7m zones 8 long 7 over 7 4 over 4 range link Count Rate Height Test 10 ft sec 1.5m sec ft recommended 2.1m may be mounted at heights see Table 1 LED with disable link 3 volt Lithium Use only No 466 DL123A CR123A CR123A or CR123A F 122 cid 176 F 0 cid 176 C 50 cid 176 C to 95 RH max non 2 11 16 W x 5 H x 1 7 8 D x 127mm x 48mm POLARITY ZONE CONSISTS 2 FIELDS 1 Pattern 3 98 5890PI INFRARED MOTION INSTALLATION Remove front cover by inserting a large blade or small coin in groove cover and base at the location in Figure 2 rotate blade to snap fit then lift cover off Observing correct polarity install the Lithium batteries supplied into the holders as shown in Figure 5 sure the batteries are firmly seated Repla ce the cover snap fit Caution of fire explosion and burns Do not disassemble heat above 100 cid 176 C or Dispose of used batteries Keep away from children Note If you have not the detector ID into the i e this is an initial detector refer to the PROGRAMMING below and perform the ID enrolling before mounting or testing the must enroll the detector ID during of the system You should the 5890PI as an type unit supervised RF and the Loop as 1 program the detector place the LED in the TEST position see Figure 5 Pulse Count jumper in the OFF position installed and cover on Temporarily the lens a cloth will do to prevent any by the detector the QED control in Zone Programming at the Input serial number prompt the cloth cover and motion your hand the lens to activate the detector and it to send a FAULT then cover the lens to send a RESTORE Repeat this to confirm the serial number Alternatively you can enter the number manually LED jumper to the NORMAL the QED control unit installation for further details HINTS Do not install where the detector is exposed direct sunlight or directly above strong of heat Make sure the detection area does not have curtains screens large pieces furniture plants etc which may block pattern of coverage Avoid locating a unit in areas which objects likely to produce a rapid in temperature such as central radiators or ducts or heaters of kind air conditioners open flame etc Do not mount on an unstable surface Mounting mounting requires the use of the No 1990MK Recess Mounting Kit instructions for the use of this kit it Note Holes C in the base accessible only when the PC is removed are used for recessed Lenses if required Remove front cover Squeeze upper lens lock located in front to release upper Fresnel lens Squeeze lower lens lock to lower Fresnel lens support see 4 Note how the supports are then remove the supports Carefully remove the existing lens and it with an optional coverage lens The lens must be with the smooth side facing Also the lens should be oriented its part number on the upper right side se