Ademco - RX4 Passive Infrared Detector

INSTRUCTIONS INFORMATION Rx4 m otion detector offers the ultim ate in perform ance w ith an com bination of detection and false alarm im m unity ptim al operation is assured w ith the follow ing advanced features M icroprocessor based algorithm s for advanced detection false im m unity processing A dem co patented A lternate Polarity Q uad detector for proved false alarm im m unity Im m une to pets and other anim als up to 45 lbs A utom atic adaptation to environm ental disturbances A dvanced dual slope tem perature com pensation D ual channel supervision that reverts to single channel operation hen a failure in the other channel is detected Zone locating w alk test m ode detector includes a standard w ide angle m irror installed and an long range curtain m irror The optional 1875PA pet m irror is also available O ptional sw ivel m ounting brackets are under part num ber 998SB and Q uest SB2 THE MIRROR Rem ove front cover by inserting a screw driver blade in the groove een the cover and base along the bottom edge and tw isting Spread either or both plastic prongs holding the w ide angle irror and rem ove the m irror See Fig 2 for location of prongs Insert one side of the long range curtain m irror under a prong and the other side under the other prong M ake sure the m irror are squarely in their corner rests and are held securely under prongs O TE M irror surface should be free of dirt foreign m atter and U se a soft dry cloth to w ipe m irror surfaces if MASKING se the supplied m asking strips to produce a protection pattern that the particular requirem ents of the protected area or to elim inate from areas w here you anticipate environm ental disturbances m ight reduce the PIR stability a heater or other heat producing for exam ple ply peel off the appropriate pressure sensitive strip s and apply the desired m irror segm ent s Each m asked m irror segm ent inates one zone of protection from the coverage pattern For the m asking strips m ay be placed on the w hite filter aterial covering the upper tier instead of on the m irror itself VIEW 7 ft 2.1m Mounting Height 8 97 DETECTOR Infrared etection M ethod overage ide A ngle M irror Range Curtain M irror 70 x 10 21.3m x 3m etection Zones ide A ngle M irror Range Curtain M irror 1 zone 7 tiers Processing zones 6 long 3 short x 45 10.6m x 13.7m etectable W alk Rate ounting H eight larm Relay V oltage at 12V perating Tem p perating H um idity im ensions or Interm ediate selectable via IP sw itch 15 1.5m sec ft 2.1m nom inal LED enabled disabled via D IP A N C 16V D C 0.13A m ax ith 15W protective resistor V D C w ith reverse polarity m A nom inal non alarm m A nom alarm LED disabled m A nom alarm LED enabled m A nom during w arm up er source should be capable of at 4 hours of battery standby F to 122 cid 176 F 29 cid 176 C to 50 cid 176 C C to 50 cid 176 C for U L installations p to 95 RH m ax non condensing x 4 3 8 H x 1 7 8 D m x 111m m x 48m m A SK IN G N O TE The segm ent opposite the zone to be elim inated the correct one to m ask For exam ple to elim inate the rightm ost m ask the leftm ost m irror segm ent PATTERNS 1 show s protective patterns for a nom inal m ounting height of ft 2.1m coverage w ill be obtained w hen the m ounting site is selected so the likely direction of the intruder is across the pattern of the ft ft ft ft AREA PATTERN PATTERN VIEW ft VIEW at 7 ft 2.1m Mounting Height VIEW ft ft ft ft ft ft ft ft ft ft ft ft ft DETECTION PATTERN OF THE IN THE INVERTED POSITION IDENTICAL TO THE PATTERN IN THE MOUNTING POSITION EXCEPT THE BEAMS TILT UPWARD 1 Coverage Patterns PET IMMUNITY Rx4 provides reasonable protection from nuisance alarm s caused pets or anim als up to 45 pounds if the follow ing guidelines are ed M ount the center of the detector at 7 feet high Set the sensitivity to Standard STD M ount w here anim als cannot com e w ithin 6 feet of the detector clim bing on furniture boxes or other objects D o not aim the detector at stairw ays that can be clim bed by the al OR CORNER MOUNTING ount the unit to a firm vertical surface The w all w iring hole should no m ore than 5 16 8m m diam eter Rem ove the front cover and PC board Referring to Figure 2 break out the desired knockout m ounting U se knockout holes A for norm al surface m ounting U se holes B for corner m ounting Break out the desired ire entry hole m arked X 1 or X 2 at the top of the detector base Feed w iring em erging from the w all through the w ire access hole M ount the base and reinstall the PC board Refer to W IRIN G CO N N ECTIO N S section before replacing the CEILING MOUNTING versatility of this detector perm its optional ceiling m ounting the Long Range Curtain m irror This provides a 15 20ft 4.5 forw ard looking curtain pattern as show n in Figure 3 The ounting procedure is the sam e as for N orm al W all M ounting that the unit is ceiling m ounted w ith the unit facing tow ard detection area CONNECTIONS Bring all w ires through the w ire access slot at the top of the base near the term inal block and connect to the screw inal See Figure 4 for term inal designations Seal any openings in the base w ith foam or RTV not supplied to drafts and insects from entering the unit A pply pow er only after all connections have been m ade and SWITCH SETTINGS se the D IP sw itch to select W alk Test N orm al m ode and Pulse options U se a sm all pointed tool to m ove the sw itch O FF or O N as desired orm al W alk Test M ode D IP position 1 orm al M ode alk Test M ode See TEST PRO CED U RES section for Processing O ption D IP position 2 Pulse Processing ecom m ended setting for m axim um false alarm m unity It tolerates environm ental extrem es on this ediate Pulse Processing m ended setting for locations w here an intruder is to cover only a sm all portion of the protected It tolerates norm al environm ents on this setting se this setting w ith the Long Range Curtain m irror Enable D isable O ption D IP position 3 the LED isable the LED screwdriver this end to open 2 Back Case w ith M irror unit so that window is towards area 12 ft 3 Detection Area with Ceiling Mounted Unit Long Range Curtain Mirror C Switch 4 W iring D etails Operation Mode Processing Processing Enabled Used Disabled in OFF position 5 D IP Sw itch Functions 2 detector provides advanced dual channel supervision and a output term inal If a failure is isolated to only one of the tw o channels the detector w ill continue to operate as a dual elem ent Continued single channel operation can be verified by w alk w ith the LED enable Even though som e operation is aintained the unit should be replaced as soon as possible a supervision failure occurs the LED w ill flash every 2 seconds of the selected LED enable disable option If the unit has to single channel operation as a dual elem ent PIR the LED ill light w hen an alarm occurs if the LED is enabled pon supervision failure the open collector TRO U BLE O U TPU T inal w