Ademco - Vista 15P Programming Manual

cid 1 cid 2 cid 3 cid 4 cid 5 cid 6 cid 7 cid 8 cid 9 cid 10 cid 11 cid 10 cid 1 cid 2 cid 3 cid 4 cid 5 cid 6 cid 7 cid 8 cid 9 cid 12 cid 13 OFF MAX TEST STAY OFF MAX TEST STAY 7 01 ENTER PROGRAMMING MODE programming requires the use of an alpha keypad connected to the keypad terminals on the control POWER UP then depress and both at once within 50 seconds of powering up key Installer Code 4 1 1 2 plus 8 0 0 different Installer Code is programmed key New Installer Code 8 0 0 was used to exit previously method 1 above must be used to enter the program mode again Field Programming Procedures to a Data Field Data a Data Field an Entry Field Number followed by the required entry the desired field number appears simply make the required entry When the last for a field is entered the keypad beeps three times and automatically displays the data field in sequence the number of digits that you need to enter in a data field is less than the maximum available for example the phone number fields 41 42 enter the desired data press The entry is terminated and the next data field number appears Field Number will be displayed for that field number No changes will be accepted in this mode Field Number Applies only to fields 45 94 and pager fields Mode Programming 57 Interactive Mode No for example The alpha display keypad will display the first of a series of prompts entries Mode Zone Programming to Program characteristics report codes alpha descriptors and serial numbers for 5800 transmitters keypad keys known as ABCD keys for special functions options as 56 mode but with fewer prompts Intended for those familiar with type of programming otherwise 56 mode is recommended module addresses and map individual relays powerline carrier devices or 4204 Relay modules Powerline Carrier devices or on board triggers Lists for relay powerline carrier activation chime zones pager zones etc alpha descriptors Function Key Programming Zone Programming mode Output Device Mapping Output Programming Zone List Programming Alpha Programming DOWNLOAD and RESET DEFAULTS Initializes download ID and subscriber account number Sets all data fields to original factory default values EXIT PROGRAMMING MODE Exits programming mode and prevents re entry by Installer Code 8 0 0 If is used to exit programming system must be powered down and method 1 above used to enter the programming mode Exits programming mode and allows re entry by Installer Code 8 0 0 or method 1 above Messages OPEN CIRCUIT no communication between Keypad and Control or ENTRY ERROR ERROR invalid field number entered re enter valid field number powering up AC dI disabled or Busy Standby and NOT READY will be displayed after approximately 4 seconds will revert to a message in approximately 1 minute which allows PIRS etc to stabilize You can bypass this by pressing 0 E4 or E8 appears more zones than the expansion units can handle have been programmed Correct the programming then completely de power and re power the control to clear this indication and remove the disable indication 2 of a number other than one specified will give unpredictable results Values shown in brackets are factory defaults shown in dashed boxes indicate partition entries for VISTA 20P only not applicable for VISTA 15P Function Data Entries Programmable Values SETUP CODE digits 0 4112 QUICK ARM ENABLE no 1 yes ACCESS CODE FOR PHONE MODULE 00 1 only 29 LONG RANGE RADIO OUTPUT disable 1 enable RF JAM OPTION FORCED BYPASS RF HOUSE ID CODE CHIME BY ZONE X HOUSE CODE SOUNDS AND TIMING ONE AUDIBLE ALARM PER ZONE FIRE ALARM SOUNDER TIMEOUT ALARM SOUNDER TIMEOUT EXIT DELAY ENTRY DELAY 1 zone type 01 ENTRY DELAY 2 zone type 02 EXIT WARNING CONFIRMATION OF ARMING DING 0,0 1 Part 2 0 0,0 1 Part 2 1 Part 2 Common 0 0 0 0 1 70,70 1 Part 2 30,30 1 Part 2 60,60 1 Part 2 1,1 1 Part 2 0,0 1 Part 2 1 no RF Jam detection 1 send RF Jam report UL must be 1 if wireless devices are used none UL must be bypass open zones disable all wireless keypad usage using 5827 5827BD or 5804BD keypad no 1 yes select zones to chime on zone list 3 81 Menu mode A 1 B 2 C 3 D 4 E 5 F 6 G H 8 I 9 J 10 K 11 L 12 M 13 N 14 O 15 P UL not for fire or UL installations disable 1st digit enter 1 2nd digit enter 11 or 12 for UL must be for UL Commercial Burg installations no UL must be 1 yes sounder stops at timeout no sounder timeout UL must be for fire install none 1 4 min 2 8 min 3 12 min 16 min UL minimum 4 min seconds of exit delay time for each partition zones use same delay as partition 1 seconds of entry delay 1 time for each UL 45 seconds max zones use same delay as partition 1 entry delay 2 time for each partition 60 seconds max zones use same delay as partition 1 no 1 yes no 1 yes wired keypads and RF yes RF only POWER UP IN PREVIOUS STATE no 1 yes UL must be PROGRAMMING the number of digits shown Do not fill unused spaces Enter 0 11 for 12 for 13 for a 2 second pause If fewer than the digits entered exit the field by pressing and next desired field number ACCESS CODE up to 6 digits To clear entries from field press PHONE No up to 20 digits To clear entries press PHONE No up to 20 digits To clear entries press 3 Entry of a number other than one specified will give unpredictable results fields 43 46 Enter 0 11 for B 12 for C 13 for D 14 for E 15 for F Enter as the fourth digit if a 3 digit account number for 3 1 dialer format is used Enter 0 as the first digit of a 4 digit account number for Nos 0000 0999 Exit field by pressing and press next field number if only 3 are used E g For Acct B234 enter 11 2 3 4 43 PARTITION 1 PRIMARY SUBS ACCT No