Ademco - Vista 20SE User Manual

SSeeccuurriittyy Manual 6 97 2 OF CONTENTS OVERVIEW Partitioned System Protection Codes Protection of Alarm Access Voice Response DELAYS Information Alarms ZONE OPERATION THE KEYPADS OF THE KEYPADS FOR OPEN ZONES PERIMETER ONLY STAY PERIMETER ONLY INSTANT ALL PROTECTION AWAY ALL PROTECTION MAXIMUM AND SILENCING ALARMS of Alarm PROTECTION ZONES Bypass Bypassed Zones MODE KEYS DEVICE COMMANDS FEATURE CODES Code Code Arming Add or Change A User Delete A User THE SYSTEM CONDITIONS ALARM SYSTEM RECOMMENDATIONS EVACUATION YOUR SYSTEM GUIDE TO SYSTEM FUNCTIONS OF AUDIBLE NOTIFICATION CREDIT REQUEST FORM 3 OVERVIEW on your ownership of an Ademco Partitioned Security System You a wise decision in choosing it for it represents the latest in security protection today Ademco is the world largest manufacturer of security systems and of premises are protected by Ademco systems system offers you three forms of protection burglary fire and emergency Your consists of at least one keypad which provides control of system operation includes various sensors which provide perimeter and interior burglary protection smoke or combustion detectors designed to provide early warning in case of fire system uses microcomputer technology to monitor all protection zones and status display appropriate information on the keypad s used with the system initiate appropriate alarms Your system may also have been programmed to send alarm or status messages over the phone lines to a central alarm station stated a partitioned system is a single physical alarm system that provides areas of protection intended for use by independent users For the most you need not know about other users and their structure in the system but from to time you may see display messages which indicate the system is in use by user Do not be concerned this is normal A partitioned system may also have common zone area which is an area shared by users of both partitions Refer to COMMON ZONE OPERATION section for details on using this feature system sensing devices have been assigned to various zones For example sensing device on your Entry Exit door may have been assigned to zone 01 devices on windows in the master bedroom to zone 02 and so on These will appear on the display along with a description for that zone if when an alarm or trouble condition occurs Partitioned 4 OVERVIEW system provides four modes of burglary protection STAY AWAY INSTANT and and allows you to BYPASS selected zones while leaving the rest of the armed You must turn on or arm the burglary protection portion of your before it will sense burglary alarms The system also provides a CHIME mode alerting users to the opening of protected doors and windows while the system is Refer to the other sections of this manual for procedures for using these following table lists the four different arming modes and the results of each Arming Mode Delay For Each Arming Mode Delay Armed Armed Codes Protection the time of installation you were assigned a personal four digit security code only to you You must enter the security code when arming and disarming the and when performing other system functions As an additional safety feature users who do not have a need to know your code can be assigned different codes Refer to the SECURITY CODES section for procedures on adding codes to the system fire protection portion of your security system if used is always active and will an alarm if a fire condition is detected Refer to the FIRE ALARM SYSTEM for important information concerning fire protection smoke detectors and emergency exit routes from the premises 5 OVERVIEW When an alarm occurs both the keypad and external sounders will sound and the will display the zone s causing the alarm If your system is connected to a monitoring station an alarm message will also be sent To stop the alarm simply disarm the system of Alarm When an alarm condition occurs the keypad displays the number s of the zone s that the problem and displays the type of alarm ex FIRE ALARM It remains until it is cleared by disarming the system see DISARMING THE SYSTEM system may include a voice module that will permit you to access the system via Touch tone phone either on premises or by call in when away The phone access will enable you to do the following Receive synthesized voice messages over the telephone regarding the status of the Access system Arm and disarm the system and perform most function commands via the telephone voice confirmation provided after each command entry information regarding the use of this feature is provided in a separate entitled PHONE ACCESS USER GUIDE which accompanies the voice the paging feature has been programmed for your system your pager will respond to conditions as they occur in your system Your pager will display code numbers the type of condition that has occurred Refer to the PAGING FEATURE later in this manual for detailed information Feature 6 DELAYS system has preset time delays known as exit delay and entry delay Whenever arm your system exit delay giv