Home » Andover Controls ACC EMX 140 Installation Guide
File preview
Click the button below to download immediately for free
Show text preview
ACC EMX 140 for EMX Menu No. 30-3001-197 A warranty is effective for 18 months starting on the the system is shipped. EMX 140 module is approximately 7.98 6.13 1.95 in. You Begin Requirements can connect one or more EMX modules to most Infinet that have an expansion port. The particular con- are covered in the ACC EMX Modules Configuration (also enclosed with this product).The configuration also tells how many inputs and outputs are allowed for a particular controller. Before you proceed, be sure the allows modules and the number and type of mod- you plan to use. first module receives power from the controller and on 24 to 26 VDC. You can add an additional EMX module or other EMX modules other than an EMX if you have an external power supply source of 24 and properly connect the modules to it. See the ACC Modules Configuration Guide for more information. EMX 140 consumes up to 110 mA at 24 VDC. Requirements sure wiring and installations comply with local, state, national electrical codes. EMX 140 operates in the same environment that any controller operates in. 1 shows the EMX 140 module. 1. The EMX 140 Module Characteristics EMX 140 and 141 have pneumatic output channels. EMX 140 has two, the 141 has one. These outputs au- convert the electronic signal to pounds per inch (psi) and operate in the range of 0 to 20 psi. EMX 142 and 143 do not have expansion port con- but have input terminals (INA and INB) that you to analog output terminals on your controller. The 142 has two, the 143 has one. The analog input ter- receive current from current outputs on your and each has a 0 to 20 mA control signal. the EMX 140 careful when unpacking the unit or units to not damage packaging material must reuse it if you ship the back for repair. AIR 2 INA RET INB AIR Unpack channel requires 20 to 30 psi of supply air. Manuals Online! – Manuals Online! – 1992 Andover Controls Corporation, 300 Brickstone Square, Andover, MA 01810 All Rights Reserved. for EMX Menu Wire EMX 142 or 143 Outputs the EMX 142 or 143, you need to run some extension between the output on the controller and the input ter- on the module. You wire from the controller output (I) terminals to the module terminals as follows: the appropriate extension wire under the INA screw the EMX module and tighten the screw down on it. the ground extension wire under the RET screw on EMX module and tighten the screw down on it. 2 illustrates the wiring for the outputs. 2. Wiring Diagram from Outputs on Infinet to Inputs on EMX 142/143 Module = 250 W the wire to the controller; then slip the wire under the I screw of an output on the and tighten the screw down on it. the ground wire to the controller; slip it under RET screw and tighten the screw down on it. the process for the INB connection. Connect the External Power Supply necessary) you are installing multiple modules, you may need an power supply. To determine what you need, refer the ACC EMX Modules Configuration Guide. If you installing an EMX 142 or 143, you require external since you are not connecting the module directly an Infinet controller via its expansion port. 3 shows where you connect the external power to the 2-pin Berg type connector on the EMX 140. Connect EMX 140 or 141 to Infinet the module to the Infinet controller as outlined in steps that follow. sure you disconnect the Infinet controller AC power before you connect any modules. at the bottom panel of your Infinet controller. On panel is an expansion port in approximately the of the panel. at the EMX 140 module. Notice that it has a on the top and on the bottom. Plug the top into the Infinet controller. you are connecting more than one EMX 140 module your Infinet controller, connect the second one to the of the first. If you connect more than one you must use an external power supply (see later).
ACC EMX 140 for EMX Menu No. 30-3001-197 A warranty is effective for 18 months starting on the the system is shipped. EMX 140 module is approximately 7.98 6.13 1.95 in. You Begin Requirements can connect one or more EMX modules to most Infinet that have an expansion port. The particular con- are covered in the ACC EMX Modules Configuration (also enclosed with this product).The configuration also tells how many inputs and outputs are allowed for a particular controller. Before you proceed, be sure the allows modules and the number and type of mod- you plan to use. first module receives power from the controller and on 24 to 26 VDC. You can add an additional EMX module or other EMX modules other than an EMX if you have an external power supply source of 24 and properly connect the modules to it. See the ACC Modules Configuration Guide for more information. EMX 140 consumes up to 110 mA at 24 VDC. Requirements sure wiring and installations comply with local, state, national electrical codes. EMX 140 operates in the same environment that any controller operates in. 1 shows the EMX 140 module. 1. The EMX 140 Module Characteristics EMX 140 and 141 have pneumatic output channels. EMX 140 has two, the 141 has one. These outputs au- convert the electronic signal to pounds per inch (psi) and operate in the range of 0 to 20 psi. EMX 142 and 143 do not have expansion port con- but have input terminals (INA and INB) that you to analog output terminals on your controller. The 142 has two, the 143 has one. The analog input ter- receive current from current outputs on your and each has a 0 to 20 mA control signal. the EMX 140 careful when unpacking the unit or units to not damage packaging material must reuse it if you ship the back for repair. AIR 2 INA RET INB AIR Unpack channel requires 20 to 30 psi of supply air. Manuals Online! – Manuals Online! – 1992 Andover Controls Corporation, 300 Brickstone Square, Andover, MA 01810 All Rights Reserved. for EMX Menu Wire EMX 142 or 143 Outputs the EMX 142 or 143, you need to run some extension between the output on the controller and the input ter- on the module. You wire from the controller output (I) terminals to the module terminals as follows: the appropriate extension wire under the INA screw the EMX module and tighten the screw down on it. the ground extension wire under the RET screw on EMX module and tighten the screw down on it. 2 illustrates the wiring for the outputs. 2. Wiring Diagram from Outputs on Infinet to Inputs on EMX 142/143 Module = 250 W the wire to the controller; then slip the wire under the I screw of an output on the and tighten the screw down on it. the ground wire to the controller; slip it under RET screw and tighten the screw down on it. the process for the INB connection. Connect the External Power Supply necessary) you are installing multiple modules, you may need an power supply. To determine what you need, refer the ACC EMX Modules Configuration Guide. If you installing an EMX 142 or 143, you require external since you are not connecting the module directly an Infinet controller via its expansion port. 3 shows where you connect the external power to the 2-pin Berg type connector on the EMX 140. Connect EMX 140 or 141 to Infinet the module to the Infinet controller as outlined in steps that follow. sure you disconnect the Infinet controller AC power before you connect any modules. at the bottom panel of your Infinet controller. On panel is an expansion port in approximately the of the panel. at the EMX 140 module. Notice that it has a on the top and on the bottom. Plug the top into the Infinet controller. you are connecting more than one EMX 140 module your Infinet controller, connect the second one to the of the first. If you connect more than one you must use an external power supply (see later).