Home » Andover Controls DIO 20 Installation Guide

File preview
Click the button below to download immediately for free
Show text preview
Installation Guide DIO 20 provides a connection for up to 20 solid state output modules for the AEclipse option. The DIO 20 module can be mounted via a DIN Rail or directly to a panel. DIO 20 includes individually fused sockets for up to 20 solid state output modules from such as Opto 22, Grayhill, Gordos, Crydom and Potter & Brumfield. You Received Installation DIO 20 module is shipped with the parts: DIO 20 is designed to be mounted to either DIN Rail or directly to a bulkhead. 20 Printed Circuit Board Plastic PCB Mounting Brackets plastic DIN Rail mounting Brackets. guide (this document) to a DIN Rail Items Required not included yet necessary for are the following: 9400 (AEclipse) controller Output module VDC Power Source Output Wires Output Modules DIN End Clamps Rail Interface cable Clamp Rail Rail Slide an end clamp into position on the DIN Tighten the holding screws. Slide a DIN Rail Mounting Bracket under PCB Mounting bracket until flush on the side. Slide the DIN Rail Mounting Bracket/PCB assembly onto the DIN Rail until with the end clamp. Manuals Online! – to a DIN Rail (continued) one end of the module PCB into the PCB Bracket. Slide the board the middle channel of the Mounting Bracket. bracket here this bracket to trap board brackets under board Slide another DIN Rail Mounting Bracket onto a PCB Bracket. Slide the DIN Rail/PCB Mounting Bracket assembly onto the board and DIN Carefully slide the assembled brackets into the center of the module ** Output Slide the remaining bracket onto the DIN Rail and position it at the end of board. Mount another end clamp. Tighten the screws on the end clamp. Directly to a Panel are four #6-sized holes (0.156 (4mm)) provided at the corners and one the center for mounting using stand-offs directly to a flat surface. The follow- illustrates the mounting dimensions of the module. (204) (399) (98) (409) * Power Fuse Status D Cable from DO80-LED Module Specifications 24VDC + 10% -15% 12 W 25-pin D connector enable 1 enable 2 enable 3 Connector Pinout: GND enable 20 Ratings: Power: [email protected] [email protected] @3A @1A @3A @3A @3A @3.5A @1A @3.5A @3.5A @3A @1A @5A @5A @3.5A @3.5A @5A & Brumfield @3A @1A @3A @5A These model numbers represent that should be compatible. physical and electrical specifica- appear to meet those of our prod- However, this list does not an endorsement of the prod- nor does it imply that the specifica- listed are accurate. Ratings listed nominal. Refer to manufacturer sheets for limitations. Controls Corporation 1996, Andover Controls Corporation Brickstone Square, Andover MA 01810 508-470-0946 Fax 1 Connection Screw Terminals Manuals Online! – Use a floating 24VDC source or a source referenced to the AEclipse ground.
Installation Guide DIO 20 provides a connection for up to 20 solid state output modules for the AEclipse option. The DIO 20 module can be mounted via a DIN Rail or directly to a panel. DIO 20 includes individually fused sockets for up to 20 solid state output modules from such as Opto 22, Grayhill, Gordos, Crydom and Potter & Brumfield. You Received Installation DIO 20 module is shipped with the parts: DIO 20 is designed to be mounted to either DIN Rail or directly to a bulkhead. 20 Printed Circuit Board Plastic PCB Mounting Brackets plastic DIN Rail mounting Brackets. guide (this document) to a DIN Rail Items Required not included yet necessary for are the following: 9400 (AEclipse) controller Output module VDC Power Source Output Wires Output Modules DIN End Clamps Rail Interface cable Clamp Rail Rail Slide an end clamp into position on the DIN Tighten the holding screws. Slide a DIN Rail Mounting Bracket under PCB Mounting bracket until flush on the side. Slide the DIN Rail Mounting Bracket/PCB assembly onto the DIN Rail until with the end clamp. Manuals Online! – to a DIN Rail (continued) one end of the module PCB into the PCB Bracket. Slide the board the middle channel of the Mounting Bracket. bracket here this bracket to trap board brackets under board Slide another DIN Rail Mounting Bracket onto a PCB Bracket. Slide the DIN Rail/PCB Mounting Bracket assembly onto the board and DIN Carefully slide the assembled brackets into the center of the module ** Output Slide the remaining bracket onto the DIN Rail and position it at the end of board. Mount another end clamp. Tighten the screws on the end clamp. Directly to a Panel are four #6-sized holes (0.156 (4mm)) provided at the corners and one the center for mounting using stand-offs directly to a flat surface. The follow- illustrates the mounting dimensions of the module. (204) (399) (98) (409) * Power Fuse Status D Cable from DO80-LED Module Specifications 24VDC + 10% -15% 12 W 25-pin D connector enable 1 enable 2 enable 3 Connector Pinout: GND enable 20 Ratings: Power: [email protected] [email protected] @3A @1A @3A @3A @3A @3.5A @1A @3.5A @3.5A @3A @1A @5A @5A @3.5A @3.5A @5A & Brumfield @3A @1A @3A @5A These model numbers represent that should be compatible. physical and electrical specifica- appear to meet those of our prod- However, this list does not an endorsement of the prod- nor does it imply that the specifica- listed are accurate. Ratings listed nominal. Refer to manufacturer sheets for limitations. Controls Corporation 1996, Andover Controls Corporation Brickstone Square, Andover MA 01810 508-470-0946 Fax 1 Connection Screw Terminals Manuals Online! – Use a floating 24VDC source or a source referenced to the AEclipse ground.