Andover Controls emx140

Infinity 140 Pneumatic Output Expansion Module EMX 140 provides a convenient, cost-effective means to add one or two pneumatic output E A T U R E S E A T U R E S E A T U R E S E A T U R E S E A T U R E S to an Infinet controller. Each pneumatic output has a range of 0 to 20 psi, and provides feedback with an on-board pressure transducer. The pressure feedback is used in a control calculation to position the pneumatic output at the desired value, using a specially-designed valve assembly. This design eliminates the need for zero and span adjustments and does require continuous consumption of air during operation. EMX 140 module can be powered directly from any of these Infinet controllers: the SCX 920, 810, TCX 850, TCX (IDX) 851, TCX 853, and TCX 855 controllers. Additional modules can be by providing power from an external 24 VDC power supply. Consult the Infinity Expansion Configuration Guide for more specific information on the use of expansion modules. Cost-Effective Pneumatic Outputs Meet Additional Point Count On-Board Pressure Transducer Pressure Feedback Non-Bleed Operation For Low Air Additional Points Provide Controller Performance Modular Design for Easy Plug-in optional factory-mounted pressure gauge is available for visual verification of each output. pneumatic output points of the EMX 140 are treated in the same manner as the built-in I/O of each Infinet controller. expansion points are assigned using Andover Plain English programming language, they are automatically added to input and output summaries, and can be used unrestricted in programs, reports, and alarms. The electrical value of on-board pressure transducer for each output can be used unrestricted in programs, reports, and alarms as well. EMX 140 is designed to be plugged into the expansion port found at the bottom of each Infinet controller. The module enclosure is intended for panel mounting, using two sheet metal screws. When used as a stand-alone I/P wiring terminations are provided for the input signal. M X 1 4 0 M X 1 4 0 M X 1 4 0 Pneumatic Output Expansion Module M X 1 4 0 E M X 1 4 0 140 Dimensional Diagram EMX 140 can be powered directly from the attached Infinet controller. modules can be powered with an external 24 VDC power supply. Consumption: mA @ 24 VDC P E C I F I C A T I O N S P E C I F I C A T I O N S P E C I F I C A T I O N S P E C I F I C A T I O N S P E C I F I C A T I O N S Range: Supply: Environment: to 120 (0 to 49 10 to 95% RH (non-condensing) Type: open class sheet metal, IP 10 1/2 x 8 1/2 x 2 (165.1W x 215.9H x 50.8D)mm Interface: expansion serial port of the local Infinet controller. of Outputs: (EMX 140) or 1 (EMX 141) to 20 psi psi nominal, 30 psi max, oil-, water-, and dust-free Connections: I.D. NPT Barb Fitting Capacity: SCIM @ 20 psi per output Consumption: air consumption during static conditions. Linearity: .55% full scale, nominal .70% over entire operating temperature range Accuracy: 1.4% full scale, nominal 3.0% over entire operating temperature range Power Connector: connector Connectors: terminals Modules /nfinet Controller:Consult the Infinity Expansion Module Configuration Guide for the maximum of inputs/outputs allowed on each particular Infinet controller. P E C I F I C A T I O N S (Cont P E C I F I C A T I O N S (Cont P E C I F I C A T I O N S (Cont P E C I F I C A T I O N S (Cont P E C I F I C A T I O N S (Cont Pneumatic Outputs, Expansion Port Pneumatic Output, Expansion Port LISTINGS 916, FCC,CE 140 141 Installed Pressure Gauge, per Output Controls Corporation Headquarters Brickstone Square