Home » Andover Controls i2 887 Controller
File preview
Click the button below to download immediately for free
Show text preview
I N F I N E T I I 887 Series Terminal Controllers Infinet II (i2) 887 is a fully programmable, low cost, general purpose controller. It has all the power of an Infinet II controller, but with small form factor. With its unique mix of three universal inputs, one Sensor/room sensor input, four triac outputs and one relay output, i2887 can be easily configured to control Heat Pumps, Fan Coils, or units. Use the i2887 for direct control of fans, staged heating and and monitoring of room temperature, outside air temperature, air temperature or occupancy status. i2887 is compact so it can be installed in tight locations with three screws; and its removable terminal connectors allow for easy the standard i2887 version uses 24 VAC input power, the i2887-L accepts incoming line voltage at 115 or 230 VAC, has an onboard and the same versatile I/O configuration. to all i2 controllers, the i2887 features Flash memory and a fast processor for faster scan times, with plenty of additional memory for data logging of your critical data. RELIABILITY WITH FLASH MEMORY i2887 non-volatile Flash memory stores your operating system and programs, so that in the event of a power loss, your will be restored when power is returned. In additon, the Flash allows for easy upgrades of your operating system via software eliminating the need to swap out proms. input configuration on the i2887 consists of three full range Universal that accept voltage (0-5VDC), digital (on/off), counter signals (up to or temperature signals. The i2887 also offers a fourth input to the Andover Smart Sensor, or any standard room temperature BUILDING SMART Compact Terminal Controller Low-cost Fan Coil Heat Pump Control Three Universal Inputs and Smart Sensor/Room Input Four Form A Triac Outputs, Form A Relay, 277 VAC Flash Memory Allows Easy Software Updates Removable Terminal Blocks for Serviceability View and Modify Information Optional Andover Sensor Display Local On-Board Service Port Typical Applications: Fan Coil Unit Heat Pump Chilled Beams Non-Volatile Flash Memory Utmost Reliability Both Application and Operating i2887 communicates with the entire Andover Controls Infinet field bus; i.e., both Infinet and Infinet II controllers, and is with Continuum CyberStation Version 1.6x or greater. Up to Infinet devices can be networked to any Andover network controller. i2887 contains five digital outputs four A Triac-based outputs plus one Form A Relay capable of switching line voltage. outputs can be used separately for on/off or control of lighting, heat, and fan units or be configured into Form K Tri-state outputs (2- for bi-directional control of dampers and (Note: Any two consecutive Triac outputs be configured as a Form K output.) All Triac are ground referenced and rated for AC only. CAPABILITIES dynamic memory of the i2887 can be for any combination of programs, alarming, and data logging using the Andover Controls Plain English language. Our object-oriented Plain language with intuitive keywords provides easy method to tailor the controller to meet exact requirements. Programs are entered the i2887 using the Continuum CyberStation. are then stored in, and executed by, the multiple i2887s is inherently easy Plain English. A complete copy of one i2887 can be loaded directly into other i2887s changing any point names or programs. In channel assignments for the i2887 are to other Infinet devices such as the i2851 easy program conversion. on back . . .) Dimensional Drawing Dimensional Drawing Drawing Drawing Drawing Drawing P E C I F I C AT I O N S Series Terminal Controllers (CONTINUED) Accuracy: 24 VAC, +10% -15%, 50/60 Hz 115/230 VAC, +10% -15%, Hz Consumption: 10 VA 32 VA Protection:
I N F I N E T I I 887 Series Terminal Controllers Infinet II (i2) 887 is a fully programmable, low cost, general purpose controller. It has all the power of an Infinet II controller, but with small form factor. With its unique mix of three universal inputs, one Sensor/room sensor input, four triac outputs and one relay output, i2887 can be easily configured to control Heat Pumps, Fan Coils, or units. Use the i2887 for direct control of fans, staged heating and and monitoring of room temperature, outside air temperature, air temperature or occupancy status. i2887 is compact so it can be installed in tight locations with three screws; and its removable terminal connectors allow for easy the standard i2887 version uses 24 VAC input power, the i2887-L accepts incoming line voltage at 115 or 230 VAC, has an onboard and the same versatile I/O configuration. to all i2 controllers, the i2887 features Flash memory and a fast processor for faster scan times, with plenty of additional memory for data logging of your critical data. RELIABILITY WITH FLASH MEMORY i2887 non-volatile Flash memory stores your operating system and programs, so that in the event of a power loss, your will be restored when power is returned. In additon, the Flash allows for easy upgrades of your operating system via software eliminating the need to swap out proms. input configuration on the i2887 consists of three full range Universal that accept voltage (0-5VDC), digital (on/off), counter signals (up to or temperature signals. The i2887 also offers a fourth input to the Andover Smart Sensor, or any standard room temperature BUILDING SMART Compact Terminal Controller Low-cost Fan Coil Heat Pump Control Three Universal Inputs and Smart Sensor/Room Input Four Form A Triac Outputs, Form A Relay, 277 VAC Flash Memory Allows Easy Software Updates Removable Terminal Blocks for Serviceability View and Modify Information Optional Andover Sensor Display Local On-Board Service Port Typical Applications: Fan Coil Unit Heat Pump Chilled Beams Non-Volatile Flash Memory Utmost Reliability Both Application and Operating i2887 communicates with the entire Andover Controls Infinet field bus; i.e., both Infinet and Infinet II controllers, and is with Continuum CyberStation Version 1.6x or greater. Up to Infinet devices can be networked to any Andover network controller. i2887 contains five digital outputs four A Triac-based outputs plus one Form A Relay capable of switching line voltage. outputs can be used separately for on/off or control of lighting, heat, and fan units or be configured into Form K Tri-state outputs (2- for bi-directional control of dampers and (Note: Any two consecutive Triac outputs be configured as a Form K output.) All Triac are ground referenced and rated for AC only. CAPABILITIES dynamic memory of the i2887 can be for any combination of programs, alarming, and data logging using the Andover Controls Plain English language. Our object-oriented Plain language with intuitive keywords provides easy method to tailor the controller to meet exact requirements. Programs are entered the i2887 using the Continuum CyberStation. are then stored in, and executed by, the multiple i2887s is inherently easy Plain English. A complete copy of one i2887 can be loaded directly into other i2887s changing any point names or programs. In channel assignments for the i2887 are to other Infinet devices such as the i2851 easy program conversion. on back . . .) Dimensional Drawing Dimensional Drawing Drawing Drawing Drawing Drawing P E C I F I C AT I O N S Series Terminal Controllers (CONTINUED) Accuracy: 24 VAC, +10% -15%, 50/60 Hz 115/230 VAC, +10% -15%, Hz Consumption: 10 VA 32 VA Protection: