Andover Controls Continuum Power Supply Reference Guide

Technical Manuals Online 1998 Andover Controls Corporation Rights Reserved part of this publication may be reproduced read or stored in a retrieval or transmitted in any form or by any means electronic mechanical recording or otherwise without prior written permission of Controls Corporation in the United States of America is a trademark of Andover Controls Corporation All other trademarks the property of their respective owners Power Supply Reference Version A Feb 1998 Controls part number 30 3001 702 information in this book is furnished for informational purposes only is to change without notice and should not be construed as a commitment Andover Controls Corporation Andover Controls Corporation assumes no for any errors or inaccuracies that may appear in this document Documents CPU Reference 30 3001 703 I O System Reference 30 3001 499 Display Module Reference 30 3001 711 Controls Corporation Brickstone Square MA 01810 470 0555 978 470 0946 Controls Corporation Manuals Online Interference equipment has been tested and found to comply with the limits for a Class A device pursuant to Part 15 of the FCC Rules These limits are designed to reasonable protection against harmful interference when the equipment is in a commercial environment This equipment generates uses and can radio frequency energy and if not installed and used in accordance with instructions in this manual may cause harmful interference to radio Operation of this equipment in a residential area is likely to harmful interference in which case the user will be required to correct the at his own expense digital apparatus does not exceed the Class A limits for radio noise emissions digital apparatus set out in the Radio Interference Regulations of the Department of Communications pr appareil num n pas de bruits radio d les applicables aux appareils num de la class A prescrites dans le sur le brouillage radio par le minist des du Canada Manuals Online Power Supply Reference Controls Corporation Manuals Online 1 Module Characteristics 2 Installation 3 Power Connection 6 Connections 9 Power Indicator Connections 10 Power Connection 11 15 16 Manuals Online Power Supply Reference Controls Corporation Manuals Online Power Supplies 865 manual describes the installation care and use of the Continuum power supply Continuum power supply modules are part of the Andover Controls Continuum intelligent building system The Continuum system allows you to cost mix and match DIN rail mounted CPU power supply and various of I O modules and user interfaces to meet your control and monitoring The power supplies offered include an impressive array of features with the standard 120 240 VAC module one model reduces or eliminates the of power failure through a built in battery back up system with integral charger allows 48VDC power based industries such as telecommunications to provide power to critical environmental monitoring and control equipment using own battery backed power systems module includes provision for an optional AC power indicator LED This option is if you mount your Continuum system within a larger control panel or enclosure and to verify power to the system from a separate location power supply modules feature a sleek lightweight casing designed for natural cooling Quick release fasteners built into the back of the module are for DIN rail mounting cid 190 no tools required These fasteners also snap into a position that features integral reinforced holes for panel mounting in non DIN Manuals Online Power Supply Reference 1 Module Characteristics following table lists the features included in the Continuum Power Supply Voltage Output 120 240 AC 50 VAC 120 240 AC 50 U VAC DC 50 to VDC W W W Input 120 240 AC 50 U standard Continuum power module provides 35 Watts of power for the CPU and modules It also contains features that reduce or eliminate the impact of power An external 24 VDC battery source may be connected to provide un power A built in battery charger assures the battery is charged at all Using standard rechargeable lead acid batteries this unit provides full UPS including all I O modules for up to 60 minutes at 35 watts power full operation of the CPU module only including modem and network with no I O power for 4 hours and backup of DRAM and real time clock for 72 hours duration These backup modes are selected and controlled through Controls Plain English programming language 120 240 AC 50 module is a non UPS version of the PS 120 240 AC 50 U This power supply a full 50 Watts of power and can also be used as a extended power source power additional I O modules directly extending the capabilities of a typical system even to remote locations DC 50 model accepts DC input voltages from to VDC which allows industries as telecommunications to provide uninterrupted power to critical environmental and control equipment using their own battery backed power systems Andover Controls Manuals Online Installation The power supply is intended for installation within the enclosure of product power supply modules can be mounted to a standard DIN rail or be directly to a panel using screws Hardware facilitating both mounting methods is as an integral part of the case design the back of each module are molded DIN rail guide fingers The design allows the to easily hook onto and slide along a standard DIN rail clamps are provided on the case that allow you to lock the module in place it is in position Manuals Online Power Supply Reference 3 the module is in the desired position it is locked to the rail by pushing the clamps inward After the bottom is secure press the top clamp inward to the operation clamps when extended provide an alternative method of mounting to the DIN You can mount the module directly to a panel using the reinforced mounting provided on each of the clamps Andover Controls Manuals Online Dimensions overall dimensions of the power supply unit are as shown mm 2.50 mm 9.0 mm Manuals Online Power Supply Reference 5 Power Connection Power Connection PS 120 240 AC 50 PS 120 240 AC 50 U PS 120 240 power supply modules are powered by an external AC source This is connected via three screw terminals located at the bottom of the unit as below The module should receive power from its own independent 120 240 50 or 60 Hz 100 VA unswitched circuit of Case AC connection consists of both terminals Hot and Neutral from the power line a third wire tied to a common Earth ground High voltage AC Power wiring should be routed to the conduit opening nearest AC power terminals Do not bundle or route AC Power wiring with low voltage input or output wiring Be absolutely certain that your installation complies with all aspects of the National Code NFPA 70 Be especially sure that your system is properly grounded sure that AC power is not applied to the power cable while you are the module or you could receive an electrical shock that is life Andover Controls Manuals Online Ground Requirements sure that all equ