Andover Controls InfiLink 200 Installation Guide

Controlling Tomorrow World 200 Guide Version Controls Corporation Manuals Online C or distribution forbidden cid 211 1992 by Andover Controls to change without notice No 30 3001 178 1992 cid 211 Controls Corporation Brickstone Square Massachusetts 01810 Rights Reserved NOTICE by the Engineering Department at Andover Controls Corporation product is subject to change without notice This document does not con any warranty express or implied Andover Controls Corporation re the right to alter capabilities performance and presentation of this at any time 200 Installation Guide Manuals Online InfiLink 200 Installation Guide presents instructions for installing InfiLink 200 on the Infinet a network of local controllers It first how to prepare the site including facts about proper ground then how to install the InfiLink 200 basic information on local area networks LANs refer to the Network Configuration Guide or ICS Network Configuration Controls Corporation Manuals Online 200 Installation Guide Manuals Online the InfiLink 200 Infinet manual covers installing the InfiLink 200 on Infinet For on how to plan and set up your network refer to the and Infinet Configuration Guide Registration warranty is effective for 18 months starting on the date the system shipped wiring must comply with all local state and national electrical 200 Installation Guide Manuals Online the InfiLink 200 the InfiLink 200 the maximum cable length for all arms on is 4,000 ft at 19,200 baud up to 32 local controllers The In 200 amplification module lets you extend Infinet beyond 4,000 or have more than 32 local controllers is also an active hub that can connect up to 127 local controllers to the in a star configuration you can install the InfiLink 200 you need to know some basic about it its dimensions and enclosure power requirements requirements and environmental requirements equipment generates uses and can radiate radio frequency energy if not installed and used in accordance with the instruction manual cause interference to radio communications It has been tested and to comply with the limits for a Class A computing device to Subpart J of Part 15 of the FCC Rules which are designed provide reasonable protection against such interference when in a commercial environment Operation of this equipment in residential area is likely to cause interference in which case the user his own expense will be required to take whatever measures may be to correct the interference 200 Dimensions 7.5 Each InfiLink 200 is 8.5 enclosure that meets UL standards 2.75 in The unit is inside a hinged 200 Installation Guide Manuals Online Requirements sure your installation complies with local state and national codes InfiLink 200 should receive power from its own independent circuit 200 requires 120 V 10 60 Hz You can select 230 50 Hz for European sites by setting two jumpers but for smoke applications you must use 120 VAC 10 60 Hz select the input voltage When you receive it it is set to 120 V for altering the input voltage are included later in this Ground Requirements sure that all hardware from Andover Controls Corporation is to true earth ground This kind of ground protects the from lightning strikes and other power surges in the area 200 Installation Guide Manuals Online cannot guarantee that the control system will operate as unless you properly ground all controllers 200 Installation Guide Manuals Online sure to have your grounds inspected before you begin the process to be sure your municipality follows the National Code Many municipalities do not and often have electrical grounds example of a substandard ground is a galvanized steel cold water As the pipe corrodes it does not act as a true ground The corro acts as an insulator raising the potential of the pipe with respect to ground lightning strikes in the area of the installation it drastically the potential of the earth of much lower potential also impact the reliability of Andover equipment properly grounded Andover Controls units respond to changes in more rapidly than poorly grounded electrical systems a poor grounded building tries to reach ground through the Andover system The surge of current can destroy electronic compo on the controller board 200 Installation Guide Manuals Online the Ground can check your ground as follows Check your ground by first inspecting the building power panel for earth ground termination If the ground is any of the following it is not adequate and must be Does not exist connected to a corroded or galvanized pipe connected using a small gauge wire smaller than 14 AWG Be sure your InfiLink 200 is connected to the ground with a copper that terminates at the distribution panel Requirements InfiLink 200 operates in rooms with temperatures ranging from 32 120 cid 176 F and with humidity up to 85 non condensing 200 Installation Guide Manuals Online the InfiLink 200 careful when unpacking the unit to not damage the packaging must reuse it if you ship the product back for repair Required 200 AC Power Cable Four No 8 Screws Cable twisted pair the InfiLink 200 as follows Before you begin open the InfiLink 200 cabinet You may find it to mount if you remove the cabinet cover and place it to one drill holes in the InfiLink 200 cabinet or board A metal shaving easily short circuit the electronics Place two standard No 8 screws in position for the two precut in the top corners of the enclosure 1 shows the location of the eyelets and corner screw holes Screw the InfiLink 200 to a wall or secure it firmly on a base using No 8 screws in the screw holes in the lower corners of the 200 Installation Guide Manuals Online Reattach the cover Screw it firmly in place 1 Locations of Screw Holes and Eyelets in Enclosure of Enclosure Width is 7.5 in in from top edge in Height 8.00 in in with in Edge Center 50 in Hole Location in from bottom edge hole is 19 of Enclosure Connector in Deep pinouts for the RS 232 connector are listed in the appendix 200 Installation Guide Manuals Online the AC Input Voltage voltage is set to 115 V when shipped To change the voltage you reset the jumpers to the right of the AC power connection 1 shows jumper settings for the two voltages 1 Connecting Jumpers for AC Input Voltages Jumpers Jumpers To E2 E3 To E3 change the voltage from 115 V to 230 V proceed as follows Disconnect the jumper end from E2 and move it to E3 so it jumpers to E3 Disconnect the jumper end from E1 to E3 and entirely remove it the controller board the AC Power sure the AC power is not connected to an electrical power source you are wiring the controller or you could receive an electrical that is life threatening AC power connection is in the lower left corner of the InfiLink 200 must wire the AC cable to the three screws on the far left 200 Installation Guide Manuals Online 2 shows the location of the AC power connection 200 Installation Guide Manuals Online 2 The Inside of the InfiLink 200 8A RATE