Autocall Duct Detector Housings with TrueAlarm Photoelectric Detector for Stand-Alone Operation

UL, ULC, CSFM Listed* Smoke Detectors Detector Housings with TrueAlarm Photoelectric Detector for Stand-Alone Operation Operation. an alarm is detected, the on-board relay contacts transfer, the control tone-alert sounds, and the alarm LED illuminates. Activating the switch will silence the tone-alert. After the source of the alarm is and resolved, turning the key switch to Test/Reset will reset the Relay Operation. output relay contacts are held energized during normal operation. loss of power or removal of the detector, the contacts will transfer. stand-alone operation air duct detector housing with cover to monitor for the presence of smoke** factory installed TrueAlarm photoelectric smoke and features: On-board TrueAlarm sensitivity drift compensation and dirt tracking Multi-function status LED indicator on detector Magnetic test that initiates an alarm and provides detailed diagnostic Clear cover allows visual inspection Test ports provide functional smoke testing access with cover in place Input power of 120 VAC, 24 VAC, or 24 VDC UL listed to Standard 268A relay output features: Fail-safe operation that is normally energized and transfers upon loss of power, or detector removal Contacts are Form C, rated 5 A @ 120 VAC or 28 VDC, resistive requires Control Station A4098-9842 Provides power-on LED, alarm LED, local tone-alert signal, local tone- silence, and keyed test/reset switch Control station is ordered separately to rectangular ducts or round ducts Minimum size is 8″ (203 mm) square or 18″ (457 mm) diameter operated functional test: Initiates alarm and displays dirt accumulation status using the detector LED dirty detectors Assists with maintenance priorities by categorizing detector status and tubes (ordered separately): Available in multiple lengths to match duct size Installed and serviced with housing in place Please note that smoke detection in air ducts is intended to provide of the presence of smoke in the duct. It is not intended to, will not, replace smoke detection requirements for open areas or non-duct applications. Operation. A4098-9687 stand-alone duct detector housings with smoke are for applications that operate independent of a fire alarm panel. They provide a TrueAlarm smoke detector for monitoring conditioning or ventilating ducts. Sampling tubes are installed into duct allowing air to be directed to the smoke detector mounted in housing. Control Station A4098-9842 a red alarm LED, a green power-on LED, a piezoelectric tone- a tone-alert silence switch, and a key switch for selecting normal mode or to initiate a test or reset operation. (This control is required.) 1: Stand-Alone Detector Housing, Front View 2: Control Station This product has been approved by the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. See CSFM Listings 3240-2269:0526 and for allowable values and/or conditions concerning material presented in this document. Additional listings may be applicable; contact your local Autocall product supplier for the latest Rev. 7 1/2020 Detector Housings with TrueAlarm Photoelectric Detector for Stand-Alone Operation Detector Selection Chart operation duct detector with internal output relay, input power is VAC, 24 VAC, or 24 VDC* A4098-9842 Test Station (ordered 1: Control Station (required, ordered separately) Station with power-on green LED, red alarm LED, tone-alert, silence and key switch for test/reset, on stainless steel plate double gang box, 3″ H x 4″ W x 2″ D (76 mm x mm x 51 mm) Stand-alone duct detector housing includes an internally mounted model A4098-9601 TrueAlarm photoelectric detector and an exhaust tube. A sized sampling tube (ordered per application) is required, refer to chart below. Tube Selection Chart, Ordered Separately Per Duct Width, Select One Duct Width (305 mm) to 23″ (330 mm to 584 mm) to 46″ (610 mm to 1168 mm) to 71″ (1168 mm to 1803 mm) to 95″ (1803 mm