Autocall IDNet Communicating Devices A4090-9101 and A4090-9106, Zone Adapter Modules

Datasheet Peripherals Communicating Devices A4090-9101 and A4090-9106, Zone Adapter Modules Monitor ZAMs Monitor ZAMs allow a single addressable point to monitor a initiating device circuit (IDC) populated with 2-wire or 4- initiating devices. Refer to Monitor ZAM Two-Wire Initiating Device Reference Chart for compatible devices. ULC, CSFM Listed, FM communications compatible Monitor ZAMs (Zone Adapter provide an addressable interface to a conventional device circuit (IDC) for Class B or Class A IDCs: A4090-9101, Class B monitoring for 2-wire or 4-wire initiating devices, power reset connections for 4-wire devices A4090-9106, Class A monitoring for 2-wire initiating devices Zone device power is supplied separately (typically from fire alarm panel) Refer to device compatibility list Monitor ZAM Two-Wire Initiating Compatibility Reference Chart use with the following Autocall fire alarm control panels: Model Series 4007ES, 4010ES, and 4100ES fire alarm control panels IDNet communications sealed construction: Enclosed design minimizes dust infiltration Mounts in standard 4 in. (102 mm) square electrical box Screw terminals for wiring connections Visible LED flashes to indicate communications Optional covers are available to allow LED to be viewed after UL listed to Standard 864 1: Series ZAM Package approximately 1/2 size) This product has been approved by the California State Fire Marshal (CSFM) pursuant to Section 13144.1 of the California Health and Safety Code. See CSFM Listings 7300-2269:0508, 7270-2269:0511, 7272-2269:0510, 7270-2269:0513, 7300-2269:0507 and 7300-2269:0567 for allowable values and/or conditions concerning material presented in this document. listings may be applicable; contact your local product supplier for the latest status. Rev. 6 03/2021 Communicating Devices A4090-9101 and A4090-9106, Zone Adapter Modules Input Voltage Current @ 24 VDC ZAM, Zone Supervision Resistor Connections Wiring Material Plate Material Range Range Selection 1: Specifications 1 address per device to 32 VDC (nominal 24 VDC) = 16 mA maximum Alarm = 72 mA maximum (actual current is by total device requirements) k 1 W terminals for in/out wiring, 18 to 14 AWG wire (0.82 to 2.08 mm2 ) to 2500 ft ( 762 m) from fire alarm control panel to 10,000 ft (3048 m) total wiring distance (including T-Taps) with Autocall, A2081-9044 Overvoltage Protectors 1/8 in. H x 4 1/8 in. W x 1 3/8 in. D (105 mm x 105 mm x 35 mm) thermoplastic metal, galvanized to 120 F (0 to 49 C) intended for indoor operation to 93% RH at 100 F (38 C) 2: ZAM Modules Adapter Module for Class B monitoring of 2-wire or 4-wire initiating devices; with power reset connections 4-wire devices Adapter Module for Class A monitoring of 2-wire initiating devices 3: Optional Adapter and Trim Plates plate to fit 4 11/16 in. (119 mm) square electrical box semi-flush mounted box surface mounted box 4: End-of-Line Resistor Harness plate with LED viewing includes mounting screws; steel No. k 1 End-of-Line Resistor Harness for A4090-9101, Class B zone 2 Rev. 6 03/2021 Communicating Devices A4090-9101 and A4090-9106, Zone Adapter Modules ZAM Two-Wire Initiating Device Compatibility Reference Chart Bases Quantity heat detectors base required smoke detectors detector housing with A4098-9601 detector Four-wire detector operation is compatible with conventional listed contact closure initiating devices. Four-wire detectors require det