Autocall 4100ES with IDNAC Addressable Fire Detection and Control Basic Panel Modules and Accessories

UL ULC CSFM Listed NYC Fire Approved Fire Control Panels with IDNAC Addressable Fire Detection and Control Basic Panel Modules and providing dual short circuit isolating output loops MINIPLEX Transponder and remote LCD and LED annunciator support RUI isolated or un isolated communications port see Standard Bay Module Details power supplies EPS provide enhanced power delivery SLCs to addressable notification appliances With IDNAC SLCs a constant 29 VDC source voltage is maintained alarm even during battery operation allowing strobes to at higher voltage with lower current and ensuring a consistent draw and voltage drop margin under both primary power and battery standby Efficiencies include lower strobe currents wiring distances up to 2 to times farther than with conventional notification support for more per IDNAC SLC and the ability to use smaller gauge wiring providing installation and maintenance savings with high assurance appliances that operate during normal system testing will also during worst case alarm conditions IDNAC SLCs are compatible with both TrueAlert ES and TrueAlert notification appliances and remote 4009 IDNAC to extend power and wiring distance even farther modules and connections Fire Alarm Network Interfaces city connections and up to five 5 ports for printers and terminals Building Network Interface Card BNIC for Ethernet connectivity Side mounted DACT assembly requiring minimal panel space DACT is with IP Communicators Emergency communications systems ECS equipment 8 channel audio or 2 channel analog audio Additional IDNet 2 communications SLCs IDNet 2 2 Modules with short circuit isolating output loops additional power supplies relays and auxiliary relays LED switch modules and panel mount printers VESDA Air Aspiration interface ASHRAE BACnet Interface TCP IP Bridges Battery brackets for seismic area protection 4100ES compatible legacy interface modules including control of non addressable NACS 8 point zone relay module each point is selectable as an IDC input or output Class A IDCs require 2 points one out and one return rated for 2 A 30 VDC resistive Configurable as normally or closed Listings reference UL 864 Fire Detection and Control UOJZ Releasing Device Service UL 1076 Proprietary Alarm Units Burglar APOU UL 2017 Process Management Equipment QVAX Emergency Alarm Control Units FSZI UL 1730 Smoke Detector Monitor UULH UL 2572 Mass Notification Systems PGWM Feature Summary provides dual configuration programs Two programs allow for optimal system protection and commissioning with one active program and one reserve downtime is because the system stays running during download 1 cabinets are available with two or three bays 2 bay cabinet shown with Autocall ES Net Fire Alarm Networks Controller top bay standard equipment 32 Bit Master Controller with color coded operator interface and switches for high confidence feedback Dual configuration program CPU convenient service port access and for up to 2500 addressable points CPU assembly includes 2 GB dedicated compact flash memory for on system programming and information storage An Enhanced Power Supply EPS and battery charger 9 A output on board IDNAC SLCs signaling line circuit for addressable control an IDNet 2 Module for addressable device control programmable function auxiliary output Also available with InfoAlarm Command Center expanded content user see data sheet AC4100 0045 addressable device interfaces include 250 point addressable device IDNet 2 SLC that supports TrueAlarm sensors and IDNet communications monitoring and control with an electrically isolated output channel allowing use with shielded or unshielded twisted or untwisted single pair wiring This product has been approved by the California State Fire Marshal CSFM pursuant to Section 13144.1 of the California Health and Safety Code See CSFM Listings 7120 2269 0546 7272 2269 0537 and 7165 2269 0542 for allowable values and or conditions concerning material presented in this document NYC Fire Dept COA 6271A Additional listings may be contact your local product supplier for the latest status Rev 21 01 2020 documentfirealarmresources com with IDNAC Addressable Fire Detection and Control Basic Panel Modules and Accessories based programmer features Convenient front panel accessed Ethernet port for quick and easy of site specific programming Modifications can be uploaded as well as downloaded for greater flexibility AND firmware enhancements are made via software to the on board flash memory Install Mode allows grouping of multiple troubles for uninstalled and devices into a single trouble condition typical with future expansion with future equipment and devices grouped into single trouble operators can more clearly identify events from the and occupied areas Module level ground fault searching assists installation and service by and isolating modules with grounded wiring Recurring Trouble Filtering allows the panel to recognize process log recurring intermittent troubles such as external wiring ground but only sends a single outbound system trouble to avoid communications WALKTEST silent or audible system test performs an automatic self test cycle Support for TrueAlarm individual analog sensing and IDNAC notification with front panel information and selection series fire detection and control panels provide extensive operator and service features with point and module suitable for a wide range of system applications An on Ethernet port provides fast external system communications expedite installation and service activity Dedicated compact flash archiving provides secure on site system information storage of job configuration files design wide variety of functional modules are available to meet specific requirements Selections allow panels to be configured for either or networked fire control operation panel compatibility with ES Net ES Network ES Net is a next generation IP based fire network uses industry standard network technology and infrastructure and for simplified network upgrades easy terminal connectivity and IP transfer between nodes and advanced network diagnostics fire alarm control panels can be upgraded to operate on an ES by adding an ES Net NIC to the panel more detailed information on ES Net consult datasheet and talk to your local Autocall product supplier Bay Description Master Controller Bay top includes a standard multi featured power supply EPS with IDNet 2 Module the master board two vertical expansion blocks and operator interface Expansion Bays include a Power Distribution Interface PDI connection of single or multiple block modules and or slot style card modules Battery Compartment bottom accepts two batteries up to 50 to be mounted within the cabinet without interfering with module 2 Module Placement in 3 Bay Cabinet Description Boxes can be close nippled each box provides convenient stud for drywall thickness and nail hole knockouts for quicker Smooth box surfaces are provided for locally cutting conduit entrance exactly where required Cabinet assembly design has been seismic tested and is certified to and CBC standards as well as to ASCE 7 categories A through F A100 7912 option for additional legacy card stabilizer brackets battery brackets as detailed on data sheet AC2081 0019 The latching front panel assembly easily lifts off for internal access Modules are power limited except as noted such as relay modules The NEMA 1 IP30 box is ordered separately and available for early Doors are available with tempered glass inserts or solid boxes and are available in platinum or red Boxes and door retainer assemblies are ordered separately per system refer to data sheet AC4100 0037 2 Rev 21 01 2020 documentfirealarmresources com with IDNAC Addressable Fire Detection and Control Basic Panel Modules and Accessories Interface Detail Reference following illustration identifies the primary functions of the operator 1 TrueAlarm