Autocall Non-Coded Manual Stations for Releasing Applications

Datasheet System Peripherals Manual Stations for Releasing Applications mounting options Surface or semi flush with standard boxes or matching Autocall boxes Flush mount adapter kit Adapters are available for retrofitting to commonly available existing selection blank area on the front of the station allows the selection of a label to the specific release application label kit is ordered separately to data sheet AC2099 0007 for standard Autocall manual stations 1 Action Push Type Manual Station shown with sample release label ULC CSFM Listed FM fire alarm stations for releasing applications Double action push and pull operation with a normally open NO Current limited model is available with series connected 560 resistor Style C operation current limited alarm open or short trouble Operation complies with ADA requirements Pull lever protrudes when alarmed Break rod is supplied use is optional Label kit provides six varieties of releasing applications ordered Screw terminals for wiring connections resistant reset key lock keyed same as Autocall fire cabinets listed to Standard 38 Action Push Type Manual Release Stations require that spring loaded interference plate marked PUSH be pushed back to the pull lever of the single action station reducing the possibility an accidental activation A firm downward pull of the lever then the alarm switch breaking an internal plastic break rod visible the pull lever use is optional Use of a break rod can provide an additional of the possibility of an accidental activation without interfering the minimum pull requirements needed for easy activation activated the pull lever latches into the alarm position and extended out of the housing to provide a visible indication reset requires the use of a key to reset the manual station lever deactivate the alarm switch If the break rod is used it must be testing is performed by physical activation of the pull lever testing can be also performed by unlocking the station housing activate the alarm switch This product has been approved by the California State Fire Marshal CSFM pursuant to Section 13144.1 of the California Health and Safety Code See CSFM Listing 7150 2269 0540 for allowable and or conditions concerning material presented in this document Additional listings may be applicable contact your local product supplier for the latest status Rev 6 03 2021 Manual Stations for Releasing Applications selection 1 Double action push operation manual release stations operation NO contact Style C operation NO contact with series 560 resistor kit select the label required for the specific release application types include Clean Agent Extinguishing Carbon Dioxide System Sprinkler and Manual release station red housing with white letters and white pull lever label kit A4099 9802 2 Accessories aluminum mount red trim plate for double gang switch box red trim plate for Wiremold box V5744 2 red mount kit break rod key for manual station reset to page 3 for dimensions for retrofit refer to page 4 for to page 4 for details Connections Range Range Color Lever Color Dimensions Instructions terminal for in out wiring for 18 AWG to 14 AWG wire 0.82 mm2 to 2.08 mm2 to 140 0 to 60 intended for indoor operation to 90 RH at 90 38 with white raised lettering and pull lever are Lexan polycarbonate or equal with red raised lettering in H x 3 3 4 in W x 1 in D 127 mm x 95 mm x 25 mm 2 Rev 6 03 2021 mounting reference Manual Stations for Releasing Applications 2 mounting reference 3 Rev 6 03 2021 mounting reference mounting For surface mounting the preferred electrical boxes the 2975 9178 Box and 2975 9022 Cast Box are shown in the illustration mounting reference Refer to Additional mounting information Manual Stations for Releasing Applications mount side view illustration shows the side view of the 2975 9178 box 3 Series manual release station 4 mount side view 4 Rev 6 03 2021 mounting information retrofit and new installations additional compatible mounting boxes and the required adapter plates the 2099 9814 Surface trim and the Semi flush trim are shown in the illustration Manual Stations for Releasing Applications mounting information 5 mounting information 6 mounting information 5 Rev 6 03 2021 Manual Stations for Releasing Applications 2021 Johnson Controls All rights reserved All specifications and other information shown were current as of document revision and are subject to change without notice listings may be applicable contact your local Autocall product supplier for the latest status Listings and approvals under Tyco Fire Security GmbH and the names listed in this material are marks and or registered marks Unauthorized use is strictly prohibited NFPA 72 and National Fire Alarm Code are registered of the National Fire Protection Association NFPA Rev 6 03 2021