Autocall Remote Emergency Telephone Equipment A2084 Series Firefighter Telephones Datasheet
File Preview
Click below to download for free
Click below to download for free
File Data
Name | autocall-remote-emergency-telephone-equipment-a2084-series-firefighter-telephones-datasheet-7349165082.pdf |
---|---|
Type | |
Size | 938.26 KB |
Downloads |
Text Preview
Datasheet Alarm Fire Alarm Systems Emergency Telephone Equipment A2084 Series Firefighter Telephones 4 Door and Trim Surface Mount 5 Door and Trim Flush Mount Pull Handle and Break Rod ULC CSFM Listed telephones provide direct communications with the Telephone Control master phone When remote phones call the master a call tone is provided to verify the request is in process exact performance may vary depending master phone equipment Two wire telephone circuits are supervised and power limited Compatible with 4100ES Series Autocall Firefighter Telephone Controls assemblies are available for the following Surface or flush mounting Backbox is ordered separately Or as separate phone sets for plugging into dedicated remote phone stations options Break rod door latch allows access during emergencies Armored cable models to minimize vandalism voice and ear caps are with adhesive Push to talk PTT phones provide input control at the remote phone Magnetic latch models with Fire Warden Station marking and LED call Additional options are listed in Table 2 and Table 3 Accessories Replacement break rod Listed to Standard 864 telephone systems provide two way communications facilities where radio communications may not be available or are They are typically used during active firefighting conditions a fire alarm investigation or during fire alarm system inspection test requires a dedicated two wire circuit typically using twisted pair wiring TSP to minimize electrical noise pickup from wiring Depending on the master control up to 6 remote and the master can be in simultaneous use For additional refer to installation instructions 579 226AC and datasheet which describes 4100ES Master phone control operation 1 Phone Station 2 Phone Station 3 Jack 976200 This product has been approved by the California State Fire Marshal CSFM pursuant to Section 13144.1 of the California Health and Safety Code See CSFM Listings 6912 2269 0545 for allowable and or conditions concerning material presented in this document Additional listings may be applicable contact your local product supplier for the latest status Rev 12 4 2021 Emergency Telephone Equipment A2084 Series Firefighter Telephones phones are typically stored in a cabinet at the central control area where they would be conveniently located for fire fighters other authorized personnel They are compatible with commercially storage cabinets Red Pluggable Phone Push to Talk This phone is the as the A2084 9014 except it is equipped with a large and easily push to talk switch located on the inside handle between the and transmitter 7 A2084 9014 Pluggable Phone phone jacks and Mounting Phone jacks are mounted on a stainless steel plate for use with pluggable phones The front is marked red FIRE EMERGENCY PHONE lettering Mounting requires a electrical box 2 in 51 mm minimum depth In out wiring is color coded 18 AWG 0.82 mm2 wire leads A2084 9001 is standard Model A2084 9023 is similar to but also provides an LED indicator powered from the phone wiring The LED is activated when Call Out is selected the Master phone a request for the responding personnel to plug in phones and communicate with the master phones cabinet mounted Information Doors and trim are painted red and available surface or flush mounting The doors are silk screened in white with FIRE EMERGENCY PHONE or other options see Table 2 Door Option This mounting type provides a glass break similar to those used in manual fire alarm stations The break rod positioned inside the door such that pulling the door handle breaks rod and allows the door to open A standard lock is also provided to authorized entry without breaking the rod Options Armored cable phones include voice and ear caps with adhesive to minimize vandalism They are also available with switches that allow the user to mute the transmitter until is required Phone handsets are constructed of Cycolac type T a ABS material Fire Warden Station This mounting type provides an cable phone and a door equipped with a magnetic latch of a lock Typical use would be where the phone is located in a access area The door is silk screened with FIRE WARDEN and a red call in request LED is mounted on the lower left of the door trim 6 Interior View of Remote Phone Cabinet With Pull Handle and Break rod phones Red Pluggable Phone The A2084 9014 emergency is ruggedly constructed of Cycolac type T a thermal ABS A coiled line cord and jack is attached Cord length is 5 ft 1.5 2 Rev 12 4 2021 Emergency Telephone Equipment A2084 Series Firefighter Telephones phone backbox and phone assemblies for backbox mounting 1 Firefigher Phone Backbox red dimensions 13 in H x 9 11 16 in W x 3 1 2 in D mm x 243 mm x 89 mm Ordered Separately one required for each Phone Assembly listed below Type MEA 2 Firefighter Phone Assemblies for Backbox Mounting see note below Cable Style Break Rod Door Handle Includes phone mounting plate and door assembly some models are agency listed by 4590 Series type number as shown in parenthesis phone assemblies require a A2975 9053 backbox ordered separately pluggable phones phone jacks and accessories 3 Pluggable Firefighter Phones pluggable phone red pluggable use with A2084 9001 or Firefighter Phone Jack Phone Jack Station single gang mount requires minimum of 2 in depth call in phone jack station for use with 976243 contact assembly phone jack station MEA Phones Accessories break rod k 1 2 W End of Line Resistor Harness ref 733 894 one required for each Class B phone circuit contact assembly for Model 976200 Phone Jack Station order station separately Marking FIRE EMERGENCY FIRE EMERGENCY FIRE EMERGENCY FIRE EMERGENCY TELEPHONE OR USE ONLY 3 Rev 12 4 2021 trim dimension reference 4 Door Trim Dimension Reference Emergency Telephone Equipment A2084 Series Firefighter Telephones 8 Surface Mount Assembly Reference 9 Flush Mount Assembly Reference 2021 Johnson Controls All rights reserved All specifications and other information shown were current as of document revision and are subject to change without notice listings may be applicable contact your local Autocall product supplier for the latest status Listings and approvals under Tyco Fire Security GmbH and the names listed in this material are marks and or registered marks Unauthorized use is strictly prohibited NFPA 72 and National Fire Alarm Code are registered of the National Fire Protection Association NFPA Rev 12 4 2021