Barber Colman MPC-8AI

MPG8AI Controller Input Module in U S A 7193 OF CONTENTS GUIDELINES THIS PACKAGE COMPONENTS AND ACCESSORIES REQUIREMENTS GROUNDING Sensing Inputs 1 Vdc Analog Inputs mA Inputs AND SETUP INFORMATION 11 an analog input module MPG8AI module that plugs directly into any of four option slots available on the MicroSmart Controller MSCMPC providing analog inputs to the MSGMPC MPC 8AI provides eight universal analog that can be configured as 1000 ohm Balco ohm platinum 4 20 mA O l 1 Vdc sensors status contact inputs NO MPC 8AI LISTINGS UL 816 Equipment UL 873 Indicating and Regulating UL 864 Smoke Control System with FCC Class as a smoke control system sub assembly to be used by itself or as part of a MicroSmart Network RCM NCM in a smoke control For smoke control applications install accordance with F 25645 Smoke Systems Manual INPUTS 8 universal inputs individually for any of the following Ohm Platinum Temperature Sensor to 240 F O l resolution to 115 C 0.06 resolution Ohm Balco Temoerature Sensor to 240 F 0.1 o F resolution C to 115 0.06 resolution 1 Vdc 0.005 volt resolution mA 0.01 mA resolution Inouts used for status monitoring of contacts ENVIRONMENT 32 to 122 to 50X 5 85 RH non condensing REQUIREMENTS MPC 8AI derives all power from associated MSC MPC 5 x 6.25 Net 12 l 2 oz 13 oz GUIDELINES equipment has been tested and found to with the limits for a Class digital pursuant to Part 15 of the FCC rules limits are designed to provide reasonable against harmful interference when the is operated in a commercial This equipment generates uses can radiate radio frequency energy and if not and used in accordance with the manual may cause harmful to radio communications Operation this equipment in a residential area is likely to harmful interference in which case the user be required to correct the interference at his expense reduce riskof fireor electrical shock install in controlled environment relatively free of beginning the installation process for the visually inspect the unit for any defects and to make sure all parts are If any flaws are detected contact your Siebe office or authorized representative Guidelines TO CONTROLLER INPUT INPUTS MAY BE FOR THE FOLLOWING 1000 OHM BALCO SENSOR SENSOR 1 A A B 1 1 WiT xB 5 PLATE INSTALLING THE MPG8AI BE SURE THAT THE CONTROLLER FULLY SEATED TO THE BACKPLATE BFFORF AND AFTFR THE IS FASTENED TO THE ENCLOSURE MPC 8AI Analog Input Module 1 Guidelines information is contained in this For further details regarding software please refer to the appropriate Guide and the MicroSmart Operator User Guide IN THIS PACKAGE MPC 8AI is supplied with One Nl I 092 MPC 8AI module circuit board Two 8 pin connectors green N100 410659 connection to analog inputs All Al8 COMPONENTS MPCXAI requires direct connection to a MSC MPC Multi purpose controller AND ACCESSORIES and TS 58000 series platinum RTD thermostats and remote sensors and and TS 81000 series Balco sensors separate platinum RTD room sensor data for special models using RJ 11 jacks setpoints and pushbutton LED REQUIREMENTS MPCSAI powered on when connected to functional MSC MPC No additional power is power supply from associated controller before installrng MPG shock and equipment than one disconnect switch may be to de energize equipment before not attempt to power the unit ON until is complete MPC 8AI is a module that fits into any of the option slots on the MSGMPC To install power from the MSCMPC and insert the into the desired option slot on the Wiring instructions diagrams and assignments are provided below installin MPG8AI be sure that the is fu i y seated to the backplate before after the backplate is fastened to the GROUNDING shield wire for the room sensor should be to chassis where the wire enters the This ensures maximum protection electrical noise and electrostatic discharge INFORMATION AND Sensing Inputs MPC 8AI allows two types of analog inputs the purpose of temperature sensing They ohm platinum RTDs 40 to 240 F ohm Balco RTDs 30 to 240 F Series tern erature sensors cannot be used the MP Gr Al module Guidelines RTD Inputs inputs provided for these sensors are All A B through Al8 A B The inputs two vire twisted pair with shield are not polarized terminate one of the to terminal A and the other wire to terminal Terminate the shield to cabinet ground closest the entry point of the wire into the enclosure off all additional wire Cut and tape the at the sensor end to prevent it from coming contact with junction box or other conductors below for wiring and setup information 1 below illustrates the numbering scheme software assignments of the platinum RTD When making these assignments the first is the option slot number on the connected controller and the second entry is the of the analog input being used example when plugged into option slot 2 analog input number 1 has an of Al 21 Al AS SHOWN BELOW NOT SLOT ON THE CONTROLLER Al8 1000 OHM SCREW ON CHASSIS TEMP RTD or Balco Resistance Sensor 2 OHM RTD 0.00375 ALPHA OHM RTD 0.00385 ALPHA SERIES