Home » Cornell Communications Keypad Station Operating Instructions A-1806D, A-1808D
File preview
Click the button below to download immediately for free
Show text preview
A-1806D REMOTE CONTROL KEYPAD programmable via keypad any 1-6 digit access code exit time delay input from momentary SPST switch -Allows remote arm and disarm functions -Keypad programmable 10-60 second exit time hour (minimum) power-loss code retention keypad must be programmed before it will operate. If the keypad contains no programming when powered up, yellow LED will flash rapidly. The user must enter the programming mode. MODE enter the programming mode, the following sequence of keys must be entered: *,0,0,*, then #. This is the mode access code. During entry of the above keys, the yellow LED will turn off. If these keys are not properly the yellow LED will again begin flashing rapidly awaiting the programming mode access code. If code is entered correctly, the yellow LED will pulse once. At this point, enter the desired 1-6 digit function access that will allow access to door functions, followed by the # key. For example, to enter function access code 1-2- enter 1,2,3,#. The keypad will acknowledge by pulsing the yellow LED twice. Now enter the exit time delay in seconds, followed by the # key (must be 10-60 seconds). For example, to program a 15 second delay, enter . The keypad is now programmed and will automatically enter the operating mode. If an invalid function access code is entered during programming (i.e., 7 digit code) the programming mode will exited leaving the previously stored function access code in place or returning to the power-up condition if no code been previously stored. Also, if an invalid exit time delay period is entered, the 10-second default value will be MODE access any door functions, the function access code must be entered followed by the key. If the correct code is the yellow LED will flash three times. Any of the three functions can now be used. To disarm the zone, press and release the key. To arm the zone, press and release the key. To initiate an exit time delay cycle, press and release the key. The yellow LED will light for the duration of time period. During this time, the door may be entered/exited without causing an alarm and will re-arm at the end of the delay period again securing the door. anytime while in the operating mode, the exit time delay cycle can be initiated by momentarily connecting 3 and 4 of the keypad together with a SPST switch. Also, at anytime while in the operating mode, the mode can be accessed to change the keypad programming by entering the programming mode access (see PROGRAMING MODE). MODE power is removed from the keypad it will not function. However, its programming will be maintained for a of 48 hours. If power is restored within 48 hours (maximum), the keypad will automatically resume If power is not restored in time to preserve the keypads programming, it will need to be re-programmed power is restored. REMOTE CONTROL KEYPAD programmable via keypad programmable 10-60 second exit time delay exit time delay input from momentary SPST switch -Allows any 1-6 digit access code hour (minimum) power-loss code retention keypad must be programmed before it will operate. If the keypad contains no programming when powered up, yellow LED will flash rapidly. The user must enter the programming mode. MODE enter the programming mode, the following sequence of keys must be entered: *,0,0,*, then #. This is the mode access code. During entry of the above keys, the yellow LED will turn off. If these keys are not properly the yellow LED will again begin flashing rapidly awaiting the programming mode access code. If code is entered correctly, the yellow LED will pulse once. At this point, enter the desired 1-6 digit function access that will allow access to door functions, followed by the # key. For example, to enter function access code 1-2- enter 1,2,3,#. The keypad will acknowledge by pulsing the yellow LED twice. Now enter the exit time delay in seconds, followed by the # key (must be 10-60 seconds). For example, to program a 15 second delay, enter . The keypad is now programmed and will automatically enter the operating mode. If an invalid function access code is entered during programming (i.e., 7 digit code) the programming mode will exited leaving the previously stored function access code in place or returni
A-1806D REMOTE CONTROL KEYPAD programmable via keypad any 1-6 digit access code exit time delay input from momentary SPST switch -Allows remote arm and disarm functions -Keypad programmable 10-60 second exit time hour (minimum) power-loss code retention keypad must be programmed before it will operate. If the keypad contains no programming when powered up, yellow LED will flash rapidly. The user must enter the programming mode. MODE enter the programming mode, the following sequence of keys must be entered: *,0,0,*, then #. This is the mode access code. During entry of the above keys, the yellow LED will turn off. If these keys are not properly the yellow LED will again begin flashing rapidly awaiting the programming mode access code. If code is entered correctly, the yellow LED will pulse once. At this point, enter the desired 1-6 digit function access that will allow access to door functions, followed by the # key. For example, to enter function access code 1-2- enter 1,2,3,#. The keypad will acknowledge by pulsing the yellow LED twice. Now enter the exit time delay in seconds, followed by the # key (must be 10-60 seconds). For example, to program a 15 second delay, enter . The keypad is now programmed and will automatically enter the operating mode. If an invalid function access code is entered during programming (i.e., 7 digit code) the programming mode will exited leaving the previously stored function access code in place or returning to the power-up condition if no code been previously stored. Also, if an invalid exit time delay period is entered, the 10-second default value will be MODE access any door functions, the function access code must be entered followed by the key. If the correct code is the yellow LED will flash three times. Any of the three functions can now be used. To disarm the zone, press and release the key. To arm the zone, press and release the key. To initiate an exit time delay cycle, press and release the key. The yellow LED will light for the duration of time period. During this time, the door may be entered/exited without causing an alarm and will re-arm at the end of the delay period again securing the door. anytime while in the operating mode, the exit time delay cycle can be initiated by momentarily connecting 3 and 4 of the keypad together with a SPST switch. Also, at anytime while in the operating mode, the mode can be accessed to change the keypad programming by entering the programming mode access (see PROGRAMING MODE). MODE power is removed from the keypad it will not function. However, its programming will be maintained for a of 48 hours. If power is restored within 48 hours (maximum), the keypad will automatically resume If power is not restored in time to preserve the keypads programming, it will need to be re-programmed power is restored. REMOTE CONTROL KEYPAD programmable via keypad programmable 10-60 second exit time delay exit time delay input from momentary SPST switch -Allows any 1-6 digit access code hour (minimum) power-loss code retention keypad must be programmed before it will operate. If the keypad contains no programming when powered up, yellow LED will flash rapidly. The user must enter the programming mode. MODE enter the programming mode, the following sequence of keys must be entered: *,0,0,*, then #. This is the mode access code. During entry of the above keys, the yellow LED will turn off. If these keys are not properly the yellow LED will again begin flashing rapidly awaiting the programming mode access code. If code is entered correctly, the yellow LED will pulse once. At this point, enter the desired 1-6 digit function access that will allow access to door functions, followed by the # key. For example, to enter function access code 1-2- enter 1,2,3,#. The keypad will acknowledge by pulsing the yellow LED twice. Now enter the exit time delay in seconds, followed by the # key (must be 10-60 seconds). For example, to program a 15 second delay, enter . The keypad is now programmed and will automatically enter the operating mode. If an invalid function access code is entered during programming (i.e., 7 digit code) the programming mode will exited leaving the previously stored function access code in place or returni