DSC 3G3070 - Installation Manual - ENG - V3 6 - R001

3G3070 HSPA WIRELESS ALARM MANUAL This manual contains information on limitations regarding product and function and information on the limitations as to liability of the manu The entire manual should be carefully read OF CONTENTS 1 1 Specifications 1 1 of Parts 2 3 the 3G3070 4 the 3G3070 4 LEDS 5 Principles 6 Landline Mode 6 Transmission Monitoring PTM 6 Communications Sequence 6 6 7 the Outputs 7 Shutdown 7 Default 7 Power Radio Shutdown 8 the Device 8 Guide 11 Wiring Diagrams 15 equipment is fixed wall mounted and shall be installed in the position specified in instructions The equipment enclosure must be fully assembled and closed with the necessary screws tabs and secured to a wall before operation Internal wiring be routed in a manner that prevents Excessive strain on wire and on terminal connections Loosening of terminal connections Damage of conductor insulation Never install this equipment during a lightning storm the end user to Not attempt to service this product Opening or removing covers may expose the user dangerous voltages or other risks Any servicing shall be referred to trained service only Use authorized accessories only with this equipment not dispose of the battery in fire or water Disposing of the battery in a fire will cause and explosion not dispose of the waste battery as unsorted municipal waste Consult your local and or laws regarding recycling with regard to this lithium battery pack Doing will help protect the environment Some of the materials that are found within the bat could become toxic if not disposed of properly and may affect the environment 3G3070 is a wireless communicator that sends alarm system information to an SurGard System I II IV or 5 receiver through a 3G HSPA or 2G EDGE GPRS wireless network The 3G3070 is designed to work with the Contact ID communication format as described in SIA DC Standard Before completing the field installation of the alarm monitoring system please ensure com with the supervising central station is successful by sending several events and getting confir that they have been received Compatible with 4 digit or 10 digit Contact ID communication format as described in SIA DC 05 Example of suitable compatible alarm panels DSC Models PC1864 PC1832 PC1616 Simulates landline Switches automatically to the 3G HSPA or 2G EDGE GPRS network in the event of landline trou e g line down Wireless Signal Indicator Four programmable outputs Contains one 12V 1.2 Ah battery Case Tamper Output Landline overvoltage protection Tri band UMTS HSPA Quad Band GSM EDGE Radio Four programmable inputs 3G HSPA 2G EDGE GPRS communication with Sur Gard System I II III IV 5 Panel transmission monitoring for up to four phone numbers Specifications input voltage to the 3G3070 can be drawn from the control panel or provided by an external power rated for the application external power limited power source The power supply must be Class 2 Power Limited Supply Ratings Input Voltage for long term operation with internal battery 13.8VDC required without internal battery 13.8VDC recommended When the input voltage drops below 13.5VDC the internal battery supplied with the 3G3070 not be charged In order to maintain a charged level for the internal battery the power supply have a minimum voltage of 13.5VDC to ensure a sufficient battery charge in all conditions of use Consumption with internal battery 120mA without internal battery 500mA Plus any current drawn from the 3G3070 AUX terminal Voltage Range 9 14VDC sealed rechargeable type rated 12V 1.2Ah or 12V 7Ah for 24hr standby time charging voltage 13.5VDC charging current 50mA Battery must be replaced every 3 5 years frequency 850 1900MHz gain 2.0dBi Specifications temperature 0 32 93 RH Maximum non condensing Specifications metal enclosure painted 138mm x 224mm x 55mm 5.4 x 8.8 x 2.2 without battery 900g 3.2oz Event Buffer communications 256 Events not viewable Telco Loop specifications TIP RING Voltage 35VDC Current 25mA Resistance 600 Ohms of Parts Figure 1 Parts O3 O4 OC AS 13 L1 L2 L3 L4 12V 20 DC IN wrap circuits are classified as Power Limited Class II Power Limited except for the battery leads which are not limited Do not route any wiring over circuit boards Maintain at least 1 25.4mm separation A mini 1 4 6.4mm of separation must be maintained at all points between Power Limited wiring and all other Limited wiring Route wires as indicated above 1 Parts Current Limitation Jumper refer to Ratings Section Casing Antenna Mounting Hardware Screw Holes 3mm Connector Card not included LEDs see page 5 Connector Switch Blocks Leads Entry Ground Wire 7Ah Battery HSPA Radio