DSC AC-100 - Installation Manual - English - Acuity Hardwired Glassbreak Detector

such as kitchens bathrooms entrances etc 2 detection Jumper J3 ON provides a sensitivity setting which is more appropriate these environments The Detector Test the detector thoroughly for placement using the AFT 100 Glass Simulator Other simulators may trip unit but will not provide accurate indi For optimum protection the detector should a direct line of sight to the protected glass Window coverings will absorb sound energy the shattering glass In these cases mount detector as close as possible to the pro glass either on an adjacent wall the or behind the window covering if possi The detector should be mounted at least 1.8m feet off the ground Do not mount the detector on the same wall as protected glass Refer to the diagram below correct and incorrect mounting locations Avoid installation near sources such as or other objects which produce continuously Do not install the detector beyond the maxi recommended range even if the AFT 100 shows additional range future in room acoustics could reduce that range Application on 24 hour loops should be unless the location is unoccupied Test false alarm immunity by creating any in the room which will likely occur the alarm system is armed Break Detector INSTRUCTIONS an Acuity AC 100 acoustic glass break sensor designed to the sounds produced by the shattering of glass The AC 100 is the result of an research program designed to study properties of glass as well as the properties of produced by the shattering of framed The result is a detector which provides sensitivity and high false alarm immu High quality manufacturing methods have combined with a meticulous final test to a detector which is superior to any other of its kind Signal Processing provides accurate of Plate Laminated Wired and Tem glass types while rejecting common false sounds Information AC 100 Detector with form A alarm contact AC 101 Detector with form A alarm contact AC 102 Detector with form C alarm contact tamper switch tamper switch Voltage 9 16 Vdc Current 25mA typical 35mA max 12Vdc Alarm Relay Contact Ratings1A 24Vdc Tamper Switch Contact Ratings0.1A 24Vdc Microphone type Omnidirectional Electret Dimensions l x w x h x 64 x 20 mm 3.5 x 2.5 x 0.8 inch Alarm duration 3 seconds Additional operating modes test mode Jumper J1 memory mode Jumper J2 of Detection Jumper J3 AC 100 glass break detector comes with a level jumper setting Jumper J3 allows the selection of one of two levels of depending on the size and acoustics of room in which the detector will be installed improves the overall false alarm immunity of detector detector is factory preset for Level 1 detection J3 OFF This is the highest sensitivity set of the detector and is designed for applica requiring high sensitivity and range such as rooms or rooms which contain a signifi amount of sound absorbing surfaces such carpets furniture drapes etc Level 1 will be for most applications rooms which are smaller and contain a signif amount of hard sound reflective surfaces 2005 Digital Security Controls Toronto Canada cid 127 www dsc com Support 1 800 387 3630 Canada US 905 760 3036 in Canada choosing a location for each AC 100 glass detector the following test should be per to ensure that it is mounted in the best location mode set up Select a location and remove the front cover of detector Use double sided tape to tempo mount the detector in the selected loca Use a 9V battery to power the detector Set the test mode Jumper J1 to the ON posi The alarm relay will latch into the alarm and will remain so until the jumper is to the OFF position after testing The detector will not respond to glass break simulator unless the test Jumper J1 is in the ON position If Alarm Memory operation is desired latching set Jumper J2 to the ON position The alarm memory indication is by disconnecting the supply volt for one second This can be done from alarm system keypad using the sensor option available on most control Replace the front cover AFT 100 Glass Break Simulator AFT 100 glass break simulator generates plate tempered glass samples Use the plate glass if you are unsure of the glass type the following when testing the detector The correct mounting location is indicated by successive detections If the detector does respond each time relocate the detector repeat the test If the windows in question are covered by or blinds place the tester behind the window coverings If the drapes prevent detection we suggest that the detector mounted behind the drapes either on an wall or on the ceiling If there are multiple windows or one large win activate the tester at the furthest point on glass the detector responds consistently it can permanently mounted using the supplied the AC 100 the location has been determined open the by pressing the release tab on the bot with a small flat blade screwdriver Remove cover and set in a safe location Draw the through the rectangular opening in the and connect to the terminal block polarity for power wiring Mount the using the two mounting screws Once detector is permanently mounted replace the and repeat the installation tests using the tester to confirm proper operation Notes This product should be tested yearly by the This product must be connected to a UL Listed alarm power supply capable of provid at least 4 hours of stand by power Warranty Security Controls warrants that for a period of twelve from the date of purchase the product shall be free of in materials and workmanship under normal use and that fulfilment of any breach of such warranty Digital Security Con shall at its option repair or replace the defective equipment return of the equipment to its repair depot This warranty only to defects in parts and workmanship and not to dam incurred in shipping or handling or damage due to causes the control of Digital Security Controls such as lightning voltage mechanical shock water damage or damage out of abuse alteration or improper application of the foregoing warranty shall apply only to the original buyer and is shall be in lieu of any and all other warranties whether or implied and of all other obligations or liabilities on the of Digital Security Controls This warranty contains the entire Digital Security Controls neither assumes nor authorizes other person purporting to act on its behalf to modify or to this warranty nor to assume for it any other warranty or concerning this product no event shall Digital Security Controls be liable for any direct or or consequential damages loss of anticipated profits loss time or any other losses incurred by the buyer in connection with purchase installation or operation or failure of this product Digital Security Controls recommends that the entire sys be completely tested on a regular basis However despite fre testing and due to but not limited to criminal tampering or disruption it is possible for this product to fail to perform expected manual shall be used in conjunction with the Manual of the alarm control panel Type mm mm Detection Range in inches and up cm and up to 18 cm to 46 cm and up cm and up to 18 cm to 46 cm 1 ft m ft m ft ft m 2 ft m ft m Not Use Not Use Not Use Not Use de bris de vitre