DSC AMB-600 - Installation Manual - English - Addressable Bravo 6 Pet-Immune Passive Infrared Detector

FCC COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance the manufacturer instructions may cause interference to radio and television reception It has been type tested and to comply with the limits for Class B device in accordance with the specifications in Subpart of Part 15 of Rules which are designed to provide reasonable protection against such interference in any residential installation there is no guarantee that interference will not occur in a particular installation If this equipment does cause to television or radio reception which can be determined by turning the equipment off and on the user is to try to correct the interference by one or more of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional The user may find the following booklet prepared by the FCC helpful to Identify and Radio Television Interference Problems This booklet is available from the U S Government Printing Washington D C 20402 Stock 004 000 00345 4 Warranty Security Controls Ltd warrants that for a period of five years from the date of purchase the product shall be of defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty Security Controls Ltd shall at its option repair or replace the defective equipment upon return of the to its repair depot This warranty applies only to defects in parts and workmanship and not to damage in shipping or handling or damage due to causes beyond the control of Digital Security Controls Ltd such as excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd Security Controls Ltd neither assumes nor authorizes any other person purporting to act on its behalf to modify to change this warranty nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss of profits loss of time or any other losses incurred by the buyer in connection with the purchase installation or or failure of this product detectors can only detect motion within the designated areas as shown in their respective installation instructions cannot discriminate between intruders and intended occupants Motion detectors do not provide volumetric area They have multiple beams of detection and motion can only be detected in unobstructed areas covered by these They cannot detect motion which occurs behind walls ceilings floor closed doors glass partitions glass doors or Any type of tampering whether intentional or unintentional such as masking painting or spraying of any mate on the lenses mirrors windows or any other part of the detection system will impair its proper operation infrared motion detectors operate by sensing changes in temperature However their effectiveness can be reduced the ambient temperature rises near or above body temperature or if there are intentional or unintentional sources of in or near the detection area Some of these heat sources could be heaters radiators stoves barbeques fireplaces steam vents lighting and so on Digital Security Controls Ltd recommends that the entire system be completely tested on a regular basis despite frequent testing and due to but not limited to criminal tampering or electrical disruption it is for this product to fail to perform as expected Information Changes or modifications not expressly approved by Digital Security Controls Ltd could void user authority to operate this equipment Digital Security Controls Ltd Canada www dscgrp com in Canada 29003076 R003 Dual PIR Detector INSTRUCTIONS AMB 600 is a specialized Dual PIR sensor which emphasizes from false alarms caused by The AMB 600 is equipped with a designed lens which enables detector to discriminate between and small to mid sized pets Signal Processing compensation and large lens design means the human will not slip by unnoticed even on a summer day Immunity against false from RF static electrical transients white light are all features designed integrated by DSC AMB 600 uses a 2 wire connection power and to communicate with the panel This simplifies wiring and installation cost The AMB 600 current draw also maximizes the of devices that can be attached to addressable loop Patented Rating 3.5 mA standby 6.5 mA with Test LED on Environment 32 to120 0 to 49 5 to 95 RH non condensing immunity 10 V m 80 A M over range 80 MHz to 1.0 GHz immunity 15 kV immunity 2.4 kV 1.2 joules detection speed 0.5 to 10 0.15 m s to 3 m s angle 100 maximum adjustment 5 to 10 heights 6 to 10 2m to 3 m nominal 7.5 2.3m 4.9 H 2.76 W 1.75 D 124.5 mm 70 mm 44.5 mm Switch Contact Rating 0.1A 30 VDC Panel Compatibility v3.0 v2 X with PC5100 interface module by one or more of the following patents Canada 2099971 US 5444432 Patterns for AMB 600 Lens the Detector a detector location that will provide the coverage required keeping in mind following potential problems Do not aim the detector at reflective surfaces such as mirrors or windows as may distort the coverage pattern or reflect sunlight directly onto the Avoid locations that are subject to direct high air flow such as near an air duct Do not locate the detector near sources of moisture steam or oil Do not aim the detector such that it will receive direct or reflected mirror Do not limit the coverage by large obstructions within the detection area such plants or filing cabinets Do not aim the detector at a stairway which a pet has access to Do not place or objects higher than 3 ft 0.9 m which a pet can climb onto e g a on a couch closer than 6 ft 1.8 m to the detector Wiring connect the AMB 600 consult the wiring diagram below open the case use a small flat blade screwdriver and gently push in the tab the bottom of the case and pull the cover straight out at the bottom Loosen printed circuit board screw and push the board up as far as it will go Using small screwdriver remove the appropriate knockouts for the mounting screws the desired wiring entrance knockouts located at the top or bottom of backplate Mount the backplate using the screws supplied screws diagonally opposite each other to prevent the case from warping Enrollment serial number located on the back of the device must be enrolled into the control panel via Installer Programming Q 8 Installer Code This is outlined for the PC4010 4020 v3.0 in the control panel Installation and for Power panels in the PC5100 Installation Manual Connect only DSC Addressable Series devices to the loop connections Connection of ANY other type of device will operation Any devices other than Addressable Series devices which power to operate must be powered separately