DSC AMP-701NP - Installation Manual - English - Addressable Universal Input Module

Digital Security Controls Cover Sheet Number Number temperature range from 60 4 140 to 0 32 120 AMP 701NP INSTALLATION ENGLISH 33 01 8.5 x 11 White Paper 0.5 2 up Instructions Master Size 8.5 X 11 of Sheets in Master 2 Sided Printing Printing Not Required Not Applicable Finished sheet size Half Letter in x 8.5 in manual shall be used in conjunction with the Installation Manual of the alarm con panel All the instructions specified within that manual must be observed Warranty Security Controls warrants that for a period of 12 months from the date of purchase the product shall be free of defects in materials workmanship under normal use and that in fulfilment of any breach of such warranty Digital Security Controls shall at its option or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in parts and and not to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Security Controls as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper application of equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether expressed implied and of all other obligations or liabilities on the part of Digital Security Controls Digital Security Controls neither assumes for nor authorizes any other person purporting to act on its behalf to modify or to change this warranty nor to assume for it other warranty or liability concerning this product no event shall Digital Security Controls be liable for any direct indirect or consequential damages loss of anticipated profits loss of time any other losses incurred by the buyer in connection with the purchase installation or operation or failure of this product Digital Security Controls recommends that the entire system be completely tested on a regular basis However despite fre testing and due to but not limited to criminal tampering or electrical disruption it is possible for this product to fail to perform as INFORMATION Changes or modifications not expressly approved by Digital Security Controls could void the user to operate this equipment 2005 Digital Security Controls Canada cid 127 www dsc com Support 1 800 387 3630 Canada US 905 760 3036 in Canada Contact Input Module Instructions AMP 701NP contact uses a 2 wire connection for power and to communicate with control panel This simplifies wiring and reduces installation cost The low current of AMP 701NP also maximizes the number of devices that can be attached to an loop AMP 701NP has three alarm input wires to which an external device can be con The wires monitor alarm tamper and trouble states Use only devices with NC contact outputs The use of any other type of device will impair the operation of the Current Rating 0.8mA Operating Environment 49 32 120 95 RH non condensing Panel Compatibility 4020 v3 x PC5010 5015 v2 x with PC5100 interface module PC5020 V3.2 with PC5100 interface module Diagram Enrollment Number serial number located on the front of the device must be enrolled into the alarm panel via Installer Programming 8 Installer Code This procedure is for the PC4020 in the control panel Installation Manual and for the Power in the PC5100 Installation Manual WARNING cid 127 only DSC Addressable Series devices to the addressable loop Connection of ANY other type of device will impair opera Any devices other than Addressable Series devices which require to operate must be powered separately manual shall be used in conjunction with the Installation Manual of the alarm con panel All the instructions specified within that manual must be observed Warranty Security Controls warrants that for a period of 12 months from the date of purchase the product shall be free of defects in materials workmanship under normal use and that in fulfilment of any breach of such warranty Digital Security Controls shall at its option or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in parts and and not to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Security Controls as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper application of equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether expressed implied and of all other obligations or liabilities on the part of Digital Security Controls Digital Security Controls neither assumes for nor authorizes any other person purporting to act on its behalf to modify or to change this warranty nor to assume for it other warranty or liability concerning this product no event shall Digital Security Controls be liable for any direct indirect or consequential damages loss of anticipated profits loss of time any other losses incurred by the buyer in connection with the purchase installation or operation or failure of this product Digital Security Controls recommends that the entire system be completely tested on a regular basis However despite fre testing and due to but not limited to criminal tampering or electrical disruption it is possible for this product to fail to perform as INFORMATION Changes or modifications not expressly approved by Digital Security Controls could void the user to operate this equipment 2005 Digital Security Controls Canada cid 127 www dsc com Support 1 800 387 3630 Canada US 905 760 3036 in Canada Contact Input Module Instructions AMP 701NP contact uses a 2 wire connection for power and to communicate with control panel This simplifies wiring and reduces installation cost The low current of AMP 701NP also maximizes the number of devices that can be attached to an loop AMP 701NP has three alarm input wires to which an external device can be con The wires monitor alarm tamper and trouble states Use only devices with NC contact outputs The use of any other type of device will impair the operation of the Current Rating 0.8mA Operating Environment 49 32 120 95 RH non condensing Panel Compatibility 4020 v3 x PC5010 5015 v2 x with PC5100 interface module PC5020 V3.2 with PC5100 interface module Diagram Enrollment Number serial number located on the front of the device must be enrolled into the alarm panel via Installer Programming 8 Installer Code This procedure is for the PC4020 in the control panel Installation Manual and for the Power in the PC5100 Installation Manual WARNING cid 127 only DSC Addressable Series devices to the addressable loop Connection of ANY other type of device will impair opera Any devices other than Addressable Series devices which require to operate must be powered separately