DSC AMP 702 IS EN NA

File Preview
File Preview
Click below to download for free

File Data

Name dsc-amp-702-is-en-na-0871645932.pdf
Type PDF
Size 612.21 KB
Downloads

Text Preview

Device Enrollment serial number located on the back of the device must be enrolled into the alarm panel via Installer Programming Q 8 Installer Code This procedure is for the PC4010 4020 v3.0 in the control panel Installation Manual and for the v2 X in the PC5100 Installation Manual Connect only DSC Addressable Series devices to the addressable loop Connection of ANY other type of device will impair operation Any other than Addressable Series devices which require power to operate be powered separately COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the instructions may cause interference to radio and television reception It has been type tested and found to comply the limits for Class B device in accordance with the specifications in Subpart of Part 15 of FCC Rules which are designed provide reasonable protection against such interference in any residential installation However there is no guarantee that will not occur in a particular installation If this equipment does cause interference to television or radio reception which be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may the following booklet prepared by the FCC helpful to Identify and Resolve Radio Television Interference Problems booklet is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 Warranty Warranty Warranty Warranty Warranty Security Controls Ltd warrants that for a period of twelve months from the date of purchase the product shall free of defects in material and workmanship under normal use and that in fulfillment of any breach of such warranty Security Controls Ltd shall at its option repair or replace the defective equipment upon return of the equipment its repair depot This warranty applies only to defects in parts and workmanship and not to damage incurred in or handling or damage due to causes beyond control of Digital Security Controls Ltd such as lightning voltage mechanical shock water damage or damage arising out of abuse alteration or improper of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties express or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd This contains the entire warranty Digital Security Controls Ltd neither assumes nor authorizes any other person to act on its behalf to modify or to change this warranty nor to assume for it any other warranty or liability this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss of profits loss of time or any other losses incurred by the buyer in connection with the purchase installation operation or failure of this product Security Controls Ltd recommends that the entire system be completely tested on a regular basis However frequent testing and due to but not limited to criminal tampering or electrical disruption it is possible for this to fail to perform as expected Digital Security Controls Ltd Canada 1 800 387 3630 www dscgrp com in Canada 29003565 R002 Fire Point Module INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS AMP 702 contact uses a 2 wire connection for power and to communicate the control panel This simplifies wiring and reduces installation cost The low current draw also maximizes the number of devices that can be to an addressable loop AMP 702 has a single EOL5.6KW supervised loop that monitors normally open only An open on the loop initiates a trouble and a short initiates an alarm AMP 702 contains an internal tamper switch to monitor tamper conditions current 1.1mA Alarm current 1.6mA Environment 0 49 32 120 95 RH non condensing H x W x D 27 x 85 x 19mm 11 16 x 33 8 x 3 4 in Panel Compatibility 4020 CF v3.0 v2 X with PC5100 interface module Diagram the connection wires through the wiring holes on the back of the unit Installations certified cUL Listed Listed 4 octagon box with or equivalent mount the unit secure the base of the unit to a UL 4 inch octagon box or equivalent UL Listed Remove the plastic cover and attach to inside of box with screws UL Listed double tape or the equivalent The open contact to be should be wired as shown in the connection The plastic cover is to be reattached to the tamper switch to electrically supervise the cover All wiring to and from the UL Listed is to meet NFPA 72 and NFPA 70 Article when used in connection to Fire Alarm When mounted in a non fire application the AMP 702 may be mounted directly the surface desired without need of additional enclosure or conduit UL Fire Installations UL Listed enclosure cUL Listed or CSA certified enclosure AMP 702 enclosure ULC Fire Installations use mount the unit secure the base of the unit to a cUL Listed or CSA certified 4 inch box or equivalent Listed enclosure Remove the plastic cover and attach to the of box with screws or the equivalent double sided tape is not permitted The contact to be monitored should be wired as shown in the connection diagram The cover is to be reattached to permit the tamper switch to electrically supervise plastic cover All wiring to and from the cUL Listed or CSA certified enclosure is to NFPA 72 ULC ORD C693 and Canadian Electrical Code Section 32 when used connection to Central Station Fire Installations When mounted in a non fire application AMP 702 may be mounted directly to the surface desired without need of additional or conduit Installations

Related Files