DSC AMP 750 IS EN NA

FCC COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd void your authority to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in accordance with the manufacturer instructions may cause interference to radio and television It has been type tested and found to comply with the limits for Class B device in with the specifications in Subpart of Part 15 of FCC Rules which are designed to reasonable protection against such interference in any residential installation However there no guarantee that interference will not occur in a particular installation If this equipment does interference to television or radio reception which can be determined by turning the equipment and on the user is encouraged to try to correct the interference by one or more of the following Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different necessary the user should consult the dealer or an experienced radio television technician additional suggestions The user may find the following booklet prepared by the FCC to Identify and Resolve Radio Television Interference Problems This booklet available from the U S Government Printing Office Washington D C 20402 Stock 004 Warranty Security Controls Ltd warrants that for a period of twelve months from the date of the product shall be free of defects in material and workmanship under normal and that in fulfillment of any breach of such warranty Digital Security Controls Ltd shall its option repair or replace the defective equipment upon return of the equipment to its depot This warranty applies only to defects in parts and workmanship and not to incurred in shipping or handling or damage due to causes beyond control of Security Controls Ltd such as lightning excessive voltage mechanical shock water or damage arising out of abuse alteration or improper application of the foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any all other warranties whether express or implied and of all other obligations or liabilities the part of Digital Security Controls Ltd This warranty contains the entire warranty Digital Controls Ltd neither assumes nor authorizes any other person purporting to act on behalf to modify or to change this warranty nor to assume for it any other warranty or liability this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential loss of anticipated profits loss of time or any other losses incurred by the buyer in with the purchase installation or operation or failure of this product Security Controls Ltd recommends that the entire system be completely tested on a basis However despite frequent testing and due to but not limited to criminal or electrical disruption it is possible for this product to fail to perform as expected 1999 Digital Security Controls Ltd Flint Road Downsview Ontario Canada M3J 2J6 416 665 8460 Fax 416 665 7498 Technical support line 1 800 387 3630 in Canada 29003950 R0 Input Output Module INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS INSTRUCTIONS AMP 750 contact uses a 2 wire connection for power and for with the control panel This simplifies wiring and reduces cost The AMP 750 low current draw also maximizes the of modules that can be attached to an addressable loop The has a single EOL5.6KW contacts only An open on the loop initiates a trouble and a short an alarm The AMP 750 contains an internal tamper switch to tamper conditions The AMP 750 has 4 open collector voltage that can be programmed to follow any of the main panel PGM Each output can supply a maximum of 5mA current For more please refer to the PC5100 v1.00 Installation manual supervised loop that monitors normally current 1.2mA Alarm current 1.6mA Environment 0 49 32 120 5 95 RH non condensing H W D 27 146 105 mm 1.05 5.76 4.13 in The standby current and in alarm current specifications do not the current draw per PGM output of the AMP 750 module To total standby current draw for your application you must add current draw per output used to the standby current specified above same applies to the total in alarm current draw Panel Compatibility v2 X with PC5100 interface module Diagram mount the unit remove the plastic cover and secure the unit to the location with the screws provided Replace the cover Enrollment serial number located on the back of the device must be enrolled into alarm control panel via Installer Programming 8 Installer Code procedure is outlined in the PC5010 5015 v2 X Installation Manual and the PC5100 Installation Manual Connect only DSC Addressable Series devices to the addressable connections Connection of ANY other type of device will impair operation devices other than Addressable Series devices which require power to must be powered separately COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd void your authority to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in accordance with the manufacturer instructions may cause interference to radio and television It has been type tested and found to comply with the limits for Class B device in with the specifications in Subpart of Part 15 of FCC Rules which are designed to reasonable protection against such interference in any residential installation However there no guarantee that interference will not occur in a particular installation If this equipment does interference to television or radio reception which can be determined by turning the equipment and on the user is encouraged to try to correct the interference by one or more of the following Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different necessary the user should consult the dealer or an experienced radio television technician additional suggestions The user may find the following booklet prepared by the FCC to Identify and Resolve Radio Television Interference Problems This booklet available from the U S Government Printing Office Washington D C 20402 Stock 004 Warranty Security Controls Ltd warrants that for a period of twelve months from the date of the product shall be free of defects in material and workmanship under normal and that in fulfillment of any breach of such warranty Digital Security Controls Ltd shall its option repair or replace the defective equipment upon return of the equipment to its depot This warranty applies only to defects in parts and workmanship and not to incurred in shipping or handling or damage due to causes beyond control of Security Controls Ltd such as lightning excessive voltage mechanical shock water or damage arising out of abuse alteration or improper application of the foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any all other warranties whether express or implied and of all other obligations or liabilities the part of Digital Security Controls Ltd This warranty contains the entire warranty Digital Controls Ltd neither assumes nor authorizes any other person purporting to act on behalf to modify or to change this warranty nor to assume for it any other warranty or liability this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential loss of anticipated profits loss of time or any other losses incurred by the buyer in with the purchase installation or ope