DSC BV-400 - Installation Manual - English - Bravo4 Quad Passive Infrared Motion Detector

INTRODUCTION 2.5 W 1.87 D 89mmH 64mmW 48mmD LENS VIEW VIEW Motion Detector INSTRUCTIONS INSTRUCTIONS QUAD element low noise sensor cid 127 Dual channel processing Four interchangeable lenses High level static protection High level transient protection High level white light immunity Excellent RF immunity Temperature compensation Energy analysis circuit LED on off jumper Vertical adjustment SMD construction Super quiet operation Wall corner mounting Small size Blends with any decor Bravo4 is a general purpose quad PIR designed to provide motion detection for large residential and commercial design care and factory testing ensure years of trouble performance Immunity against false alarms from RF static transient and white light are all designed in features analysis dual channel signal processing temperature and large multi beam lens design means the human will not slip by unnoticed even on a hot summer day interchangeable lenses wall or corner mounting and vertical provide application versatility and your client will the small size and elegant simplicity of the case design voltage 9.5VDC 14.5VDC voltage ripple 3.0V pp 12VDC current 18mA in alarm 16mA rating alarm tamper 100mA 24VDC contact resistor in common 10 ohm temperature 0 to 49 to 120 temperature 40 to 60 to 140 humidity 5 to 95 RH non condensing humidity up to 99 RH non condensing immunity 20 V m over range 0.01MHz 1.2GHz immunity 25kV immunity 2.4kV 1.2 joules light immunity 20,000 Lux at the detector detection speed 0.5 to 10 0.15m 3m s angle wall to wall lens 90 minimum adjustment 5 to 10 see charts heights 6 to 10 nominal 7.5 to 3m nominal 2.3m to 5 pet alley only to 1.5m pet alley only White light and RF Immunity not verified by UL to Wall lens BV L1 50 L 60 W 16m 18m lens BV L2 lens BV L3 Alley lens BV L4 60 L 5 W 18m 1.5m 50 L 4.4 W 16m 1.3m 50 L 60 W 16m case with light gray lens WEIGHT oz 190 g A alarm contact A alarm contact tamper switch C alarm contact tamper switch LENS VIEW VIEW ft m ft m ft m ft m ft m ft m ft m LENS VIEW PATTERN CHART THE CENTRE OF EACH BEAM PAIR ft m ft m ft m VIEW ft m ft m open the case use a small flat blade screwdriver and gently in the tab at the bottom of the case and pull the cover out at the bottom Loosen the PCB screw and push the up as far as it will go Using a small screwdriver remove appropriate knockouts for the mounting screws Remove left and or right wiring entrance knockouts located at the top the backplate Mount the backplate using the appropriate screws not supplied HEIGHT CHART FOR FULL RANGE CORRIDOR CURTAIN ALLEY 3 m m 2.4 m 2.1 m 1.8 m 1.5 m 1.2 m THE DETECTOR TESTING a detector location that will provide the coverage keeping in mind the following potential problems Surfaces Do not aim the detector at reflective such as mirrors or windows as this may distort the pattern or reflect sunlight directly onto the detector Flow Avoid locations that are subject to direct high air flow as near an air duct outlet Do not locate the detector near sources of steam or Do not aim the detector such that it will receive direct or mirror sunlight If there are pets on the premises use the pet alley lens Do not limit the coverage by large objects the detection area such as plants or filing cabinets ADJUSTMENT the Mounting Height Chart set the vertical adjustment to the desired coverage Ensure that the PCB retaining is tightened just enough to prevent board movement J1 will enable disable the alarm LED If J1 is OFF LED will not operate on alarm If J1 is ON the LED will on alarm The corridor lens should not be used in corridors that less then 5 in width and the installation should be carefully to ensure that the beams are aimed directly down the of the corridor mA VDC mA VDC mA VDC 12V GND NC C shown with power applied no alarm This unit is UL Listed should be connected to a control unit or power providing at least 4 of standby power LENSES Bravo4 is supplied with the lens To the lens release the top tab and pull the lens holder This action releases the lens Insert the lens with the FACING INWARD The bottom of the lens is by two triangular indentations Ensure that the lens centred left to right then reinstall the lens holder The lens will snap into place sealing the lens into position the detector has been set up walk test the entire area coverage is desired Should the coverage be incomplete or relocate the detector to obtain full coverage Once is as required the alarm LED may be disabled by J1 to OFF NOTE Upon installation the unit should be tested to verify proper operation detector should be walk tested weekly by the end user and by the installer and DM W Mounting Brackets the optional DM W Wall Mount and DM C Ceiling Mount to solve difficult placement problems The DM W and mount to either the wall or ceiling and allow for full vertical horizontal positioning of the motion detector the detector be tilted up or down and rotated through 90 to obtain the position for optimal coverage The Bravo PIR has been to be fully compatible with the DM W and DM C Contact your DSC distributor for more information KNOCKOUTS SCREW FOR ADJUSTMENT 12V GND NC C ON LED ON OFF LED OFF SENSOR MOUNT MOUNT Warranty Security Controls Ltd warrants that for a period of 12 months from the date purchase the product shall be free of defects in materials and workmanship under use and that in fulfilment of any breach of such warranty Digital Security Ltd shall at its option repair or replace the defective equipment upon of the equipment to its repair depot This warranty applies only to defects in and workmanship and not to damage incurred in shipping or handling or due to causes beyond the control of Digital Security Controls Ltd such as excessive voltage mechanical shock water damage or damage arising of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original purchase and is and shall in lieu of any and all other warranties whether expressed or implied and of all obligations or liabilities on the part of Digital Security Controls Ltd Digital Controls Ltd neither assumes nor authorizes any other person purporting act on its behalf to modify or to change this warranty nor to assume for it any other or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or damages loss of anticipated profits loss of time or any other losses by the buyer in connection with the purchase installation or operation