DSC BV 500GB IS EN NA UL

File Preview
File Preview
Click below to download for free

File Data

Name dsc-bv-500gb-is-en-na-ul-4315920678.pdf
Type PDF
Size 683.43 KB
Downloads

Text Preview

View at 8 ft 2.4 m height Rating Alarm Relay PIR 0.1A 24VDC Alarm Relay Glassbreak 1.0A 24VDC Tamper Switch 0.1A 24VDC diameter x height x 1.4 117 mm x 36 mm Detector Range diameter Detector placed 8 ft 2.4 m from floor 24 ft 7.3 m Detector placed 10 ft 3.0 m from floor 30 ft 9.2 m Detector placed 12 ft 3.6 m from floor 40 ft 12.2 m Detector Range x WL x WL x WL x WL x W Range Range Range Range Range Max Range Max Range Max Range Max Range Max Range 1 Detection 1 Detection 2 Detection 2 Detection 1 Detection Level 2 Detection 2 Detection 1 Detection 1 Detection 2 Detection 7.5m 4.6m 4.6m 6m not use not use J4 Motion LED ON OFF J5 Glassbreak Detection Level and up 1 4 6.35mm 12 x12 0.3x0.3 m to 0.45x0.45m and up 12 x12 0.3x0.3 m to 0.45x0.45m Setting J1 Installer Test Mode J2 Alarm Memory J3 PIR Sensitivity range test AFT 100 latch for glassbreak detection motion enabled motion 2 detection with glassbreak sensitivity operation operation detection motion disabled motion 1 detection with glassbreak sensitivity For UL Installations only Level 1 detection must be used RF Immunity Not verified by UL 10V m 80 AM 1KHz from 80MHz to 1GHz 10V 80 AM 1KHz from 150KHz to 80MHz Transients wiring terminal 2.4KV 1.2joules Operating temperature 32 122 0 50 Humidity 5 95 RH non condensing verified to 85 by UL Information BV 500GB Form alarm contact motion form alarm glassbreak BV 501GB Form alarm contact motion form alarm glassbreak and tamper switch BV 502GB Form alarm contact motion and glassbreak tamper switch View Mount PIR and Detector INSTRUCTIONS INSTRUCTIONS Bravo 5GB is a ceiling mount motion and glassbreak detector one housing designed to provide reliable protection for residential commercial applications The Bravo 5GB uses a special lens made for 360 detection in conjunction with a quad PIR sensor optimized for uniform detection all around its of view Special attention is given to false alarm immunity RF static electrical transient to ensure trouble free operation many years Bravo 5GB is integrated with an advanced microprocessor glassbreak sensor designed to detect the sounds produced the shattering of framed glass The glassbreak detection used on Bravo 5GB is a result of an extensive research designed to study the properties of glass as well as the of sounds produced by the shattering of framed glass Bravo 5GB offers a benefit of having motion and glassbreak in one housing for many applications where both are required in the same room 360 coverage High level static and transient protection Excellent RF immunity Detection Multi Level Signal Processing Quad element PIR sensor Temperature compensation Fast Slow detection jumper J3 LED ON OFF jumper J4 Super quiet operation Detection Microcontroller based Digital Signal Processing technology Dynamic Signal Processing provides accurate detection of laminated wired and tempered glass types while rejecting or type sounds noise rejection mechanism Installer test mode for glassbreak sensor Alarm memory latching LED for glassbreak sensor Input Voltage 9 14.5 VDC Current typical 38 35 mA alarm on off 12VDC the Detector Bravo 5GB is designed to be on the ceiling of a dry location for 360 coverage that the expected path of intruder is perpendicular to the path Use the coverage indicated on the diagram determine the best sensor optimum glassbreak protection the detector should have a view of the protected glass Curtains blinds and other coverings will absorb sound energy from the shattering In these cases mount the detector as close as possible to protected glass installation near noisy sources such as speakers or other which produce sounds continuously Do not install the beyond the maximum recommended range even if the shows additional range future changes in room acoustics reduce that additional range The AFT 100 Glassbreak Simulator will provide the most and accurate indication of the correct mounting location for detector Other simulators may trip the unit but will not provide indications the mounting location and the area being protected for the potential problems For the glassbreak sensor test false alarm by creating any sounds in the room which will likely occur when detector is armed Avoid following sources of false alarms Surfaces not aim the detector at reflective surfaces such as mirrors or as this may distort the coverage pattern or reflect sunlight onto the detector Flow locations that are subject to direct high air flow such as near air duct outlet not locate the detector near sources of steam or oil Sun not aim the detector such that it will receive direct sunlight not limit the coverage by placing large objects within the detection such as plants high shelves filing cabinets etc Sources the Bravo 5GB is designed to be immune from ringing and white noise sounds avoid mounting the detector near such i e telephones doorbells alarm bells sirens air conditioner water pipes etc open the case remove the securing screw from the unit then gently the top cover counter clockwise and lift it up from the bottom Using a small screwdriver to remove the appropriate knockouts wiring mount the backplate using the appropriate mounting not provided close the case use the locating line on the bottom cover to align tab on the top cover Once the top cover is engaged twist the cover clockwise to lock it in place Replace the securing screw for UL Listed applications Since no adjustment is necessary for the circuit board it is not that the installer remove the circuit board from the case not touch the microphone to the following diagram for wiring instructions Contacts shown with power applied and no alarm up the Level of Detection Jumper J5 Bravo 5GB comes with a level jumper Jumper J5 which allows the selection of one of 2 of detection depending on the size and acoustics of room in which the detector will be installed This feature better selection of the required sensitivity thereby the overall false alarm immunity of the detector detector is factory preset for level 1 detection Jumper This is the highest sensitivity setting of the detector is designed for applications requiring high sensitivity range such as larger rooms or rooms which contain a amount of sound absorbing surfaces such as furniture drapes etc rooms which are smaller and contain a significant of hard sound reflective surfaces such as kitchens entrance vestibules etc level 2 detection J5 ON provides a lower sensitivity setting which more appropriate for these environments most applications the default setting of level 1 detection J5 OFF will be the best choice Up application of power the LED will be on for approximately 90 to indicate that the unit is warming up Jumper J4 ON After 90 second warm up period the LED will turn off and the unit will to motion in the protected area NOTE Upon installation the unit should be thoroughly to ensure proper working order The detector should be walk tested by the user and annually by the installer Test Set PIR LED jumper J4 to the ON position Close the top cover Create movement in the entire area where coverage is desired The on the unit will turn on whenever motion is det

Related Files