DSC COMMUNIQUE v1 1 - Installation Manual - English - Communique Phone System

This manual contains information on limitations regarding product use and function and on the limitations as to liability of the manufacturer The entire manual should be W A R N I N G read Manual Version 1.1 of Contents Introduction Cards 2 Cards 2 Stations 2 of the Box 2 Started Steps 3 Descriptions 3 Wiring 3 Programming PIN 5 System Timers 5 Line Programming 6 Analog Interface Unit DAI 6 System PGM Outputs 6 Music or Ringback During Transfer 7 Serial Port Baud Rates 7 No Answer Options 7 List Initialization 8 Ringing and Access 8 Station 9 Notification 9 Port Assignment 9 Do Not Disturb 9 Line Preference 9 Call Display Lines 9 Pulse or Tone Dialing 10 Keys F A P 10 Factory Default Programming 10 Worksheets the Record 11 and System PIN 12 Timers 12 Line Programming 12 Analog Interface Unit Programming 8 max 12 System PGM Outputs 12 Music or Ringback During Transfer 12 Serial Port Baud Rates 13 No Answer Options 13 List Initialization 13 Ringing and Access 13 Fax Station See DAI Unit Installation Instructions details 14 Notification 14 Port Assignment See Modem Card Installation for details 14 Do Not Disturb 14 Line Preference 14 Call Display Lines 15 Pulse or Tone Dialing 15 Station Ring Cadence 15 Keys 15 Initialization 15 Control Panel Wiring Diagram L de l Canada identifie le mat homologu Cette que le mat est conforme certaines normes de protection d et de des r de t Industrie Canada n toutefois pas que le fonctionnera la satisfaction de l d ce mat l doit s qu est permis de le raccorder aux de l locale de t Le mat doit en suivant une m accept de raccordement L ne doit pas oublier qu possible que la conformit aux conditions ci dessus n pas la du service dans certaines situations r de mat homologu doivent effectu par un centre d autoris d par le fournisseur La compagnie de t peut l de d un appareil la suite de r ou de modifications par l ou cause de mauvais fonctionnement sa propre protection l doit s que tous les fils de mise la terre de la d les lignes t et les canalisations d m y en a sont raccord ensemble Cette pr est particuli importante dans r rurales L ne doit pas tenter de faire ces raccordements lui m doit avoir recours un service d des installations ou un le cas de charge IC assign a chaque dispositif terminal indique pour toute le pourcentage de la charge totale qui peut raccord un circuit t utilis par ce dispositif La terminaison du circuit boucl peut constitu de quelle combinaison de dispositifs pourvu que la somme des indices de charge de des dispositifs ne d pas 100 REN 1.4B DC REN 1.2 The Industry Canada label identifies certified equipment This certification means the equipment meets certain telecommunications network protective operational and requirements Industry Canada does not guarantee the equipment will operate to the satisfaction installing this equipment users should ensure that it is permissible to be connected the facilities of the local telecommunications company The equipment must also be using an acceptable method of connection The customer should be aware that with the above conditions may not prevent degradation of service in some to certified equipment should be made by an authorized Canadian maintenance designated by the supplier Any repairs or alterations made by the user to this or equipment malfunctions may give the telecommunications company cause to the user to disconnect the equipment should ensure for their own protection that the electrical ground connections of the utility telephone lines and internal metallic water pipe system if present are together This precaution may be particularly important in rural areas Users should not attempt to make such connections themselves but should the appropriate electric inspection authority or electrician as appropriate Load Number LN assigned to each terminal device denotes the percentage of the total to be connected to a telephone loop which is used by the device to prevent overloading termination on a loop may consist of any combination of devices subject only to the that the total of the Load Numbers of all the devices does not exceed 100 REN 1.4B DC REN 1.2 Introduction 1 Processor Board Eight stations expandable to 24 Two telephone lines expandable to eight A 100 call log of caller name number time and date call can be viewed at any telephone station call feature must be enabled by local telephone Four programmable outputs can be programmed to when any or a selected line rings when a is performed or to activate an electric door from any telephone or internal intercom station RCA input connect audio equipment for an external of system background and hold music Paging output In addition to using built in telephone intercom speakers connect additional external for paging