DSC DLM-7 - Installation Manual - Downlook 7 Camera Expansion Module
File Preview
Click below to download for free
Click below to download for free
File Data
Name | dsc-dlm-7-installation-manual-downlook-7-camera-expansion-module-1208697534.pdf |
---|---|
Type | |
Size | 653.19 KB |
Downloads |
Text Preview
DLM 7 Downlook Camera Selector Module INSTRUCTIONS 11 14.5VDC Operating Current 35mA Up to seven 1VP P CCIR NTSC or PAL compatible cameras Video out terminal for local video monitor with 75W impedence the Panel is suggested that the DLM 7 Camera Selector Module and the DLM 1 Module be mounted in a DLC 1 Cabinet The DLC 1 Cabinet has designed especially for use with Downlook components attaching the cabinet to the wall press nylon printed circuit mounting studs into the raised mounting holes from the back the cabinet Mount the cabinet securely to the wall It is that appropriate wall anchors be used when securing panel to drywall plaster concrete brick or other similar surfaces the DLM 7 circuit board from the cardboard packaging the DLM 7 Module onto the nylon mounting studs Input Connections DLM 7 Module uses NTSC or PAL compatible cameras Use a CCIR camera as older types may not function properly with DLM 7 Module the camera mounting hardware as per the manufacturer and mount the camera Connect the camera to a and align the camera with the target area and adjust the focus If an on site monitor is to be permanently connected the camera and the DLM 7 module the monitor connection be high impedance the first camera to the VIN1 terminal and remove the clip from J102 If only one camera is used with the DLM 7 should be connected to input VIN1 Connect additional cameras BNC connectors VIN2 through VIN7 Up to seven cameras may connected to the DLM 7 Requirements DLM 7 Camera Selector usually does not require an additional supply to the DLM 1 Module power is removed from all components before making between the Downlook modules Connect the DLM 7 to the DLM 1 Module with the 10 pin ribbon cable supplied to the connection diagram below and ensure that the ribbon is oriented properly J102 through J108 J102 through J108 are used to terminate unused video If a video input is not used short the pins for the terminal one of the supplied jumper clips If a camera is connected a terminal remove the clip from the jumper Video Output monitor may be connected to the DLM 7 to allow for local video The monitor will display the image from the currently camera Connect a monitor with a high input impedence to VIDEO OUT terminal If required picture quality at the local may be adjusted with part R129 Use a small screwdriver adjust part R129 do not force the adjustment screw beyond its range of motion Programming DLM 7 itself requires no programming Refer to the Installation of the security system used with the Downlook system for on programming the system for use with multiple cameras following restrictions apply to UL Listed applications The picture count shall not exceed 2 The message data format must be Sur Gard 7 3 Communication must be made to the listed Sur Gard MLR2 DG with the MLRV method employed The DLM 1 and DLM 7 must be connected to only UL Listed video The module has been found to be compatible with the UL Listed P 16 and P 1664 units only R1 WARRANTY Security Controls Ltd warrants that for a period of twelve months from the date of purchase the product shall be free of defect in and workmanship under normal use and that in fulfilment of any breach of such warranty Digital Security Controls Ltd shall at its repair or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in and workmanship and not to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Security Ltd such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether expressed implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd This warranty contains the entire warranty Digital Controls Ltd neither assumes nor authorizes any other person purporting to act on its behalf to modify or to change this warranty to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss of anticipated profits loss of or any other losses incurred by the buyer in connection with the purchase installation or operation or failure of this product Digital Security Controls Ltd recommends that the entire system be completely tested on a regular basis However despite testing and due to but not limited to criminal tampering or electrical disruption it is possible for this product to fail to perform expected Compliance Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to use equipment equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause interference to radio communications However there is no guarantee that interference will not occur in a particular installation this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio television technician for help user may find the following booklet prepared by the FCC useful to Identify and Resolve Radio Television Interference This booklet is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 1996 Digital Security Controls Ltd Flint Road Downsview Ontario Canada M3J 2J6 416 665 8460 Fax 416 665 7498 Tech line 800 387 3630 R1