DSC FSA-410 - installation manual - English

Series Smoke Detector and Operating Instructions this instruction sheet thoroughly before installation and use of the 4 Wire Smoke Detector This instruction sheet is intended to be used the Installation Manual of the alarm control panel All the instructions spec within that manual must be observed Test Button magnet here smoke detector has a nominal fixed alarm sensitivity refer the Specifications on the last page and it will go into alarm the signal level exceeds the alarm threshold and acti the alarm relay to send the alarm signal to the control During an alarm the LED will flash once per second and siren will sound the the evacuation temporal pattern Alarm Interconnection detectors with sirens can be connected using the Polarity Reversal Module When a fire alarm occurs panel will signal the PRM 4W to reverse the polarity of the loop This will activate the sirens of all units connected the loop Refer to the PRM 2W 4W Installation Instructions installation details Drift Compensation detector automatically compensates for induced changes to maintain a constant sensitivity When the drift compensation has reached high or low limit of adjustment the detector will go into trouble state Alarm heat detector will go into alarm when the heat signal exceeds the heat alarm threshold 135 and the alarm signal to the control panel The detector will go into heat alarm if there is a rapid increase in the tem over a short period of time During an alarm the LED flash once per second and the siren will sound the evac temporal pattern Indications Sensitivity Production Range Flash 1 50s 1 1s Smoke Heat 1 1s Restore Alarm 1 50s Power Trouble Trouble Switch Failed Switch Pass 1 1s 1 50s Deactivated 1 50s Deactivated for installation recommendations NOT locate smoke detectors at the top of peaked or ceilings the dead air space in these locations may pre the unit from detecting smoke Avoid areas with turbu air flow near doors fans or windows Rapid air around the detector may prevent smoke from the unit Do NOT locate detectors in areas of high NOT locate detectors in areas where the temperature rises 38 100 or falls below 5 41 Siren P A A I I N N T T N N O O T T Marks FSA 410 is a 4 wire photoelectric smoke detector with the available options fixed temperature and rate of rise detector internal piezoelectric alarm auxiliary form C and or remote LED output Three versions are available version UL Canadian version ULC and an International EU Heat detection based on rate of rise has not been by UL ULC every 7 to 8 seconds the unit tests for a smoke heat alarm condition During this sequence the unit also self diagnostics and checks for faults During normal the LED will flash every 50 seconds and the siren will sound Alarm Instructions Smoke Detector Placement smooth ceilings detectors be spaced 9.1M 30 feet as a guide Other spacing be required depending on height air movement the of uninsulated etc Consult National Fire Code NFPA 72 Chapter 11 other appropriate national smoke detectors in accordance with NFPA 72 11 detectors shall be installed outside of sleeping area in the immediate vicinity of the bedrooms on each additional story of the family living unit including and excluding crawl spaces and unfinished attics new construction a smoke detector shall also be installed in sleeping room Mount Smoke Detector Backplate backplate using screws and the appropriate holes the mounting plate Install wiring in accor with and local electrical codes UL ULC Installations the power must be supplied from a Listed alarm control unit The dust cover pro the unit when not in service dust cover before use Wiring to the wiring diagrams in this installation sheet and provided in the Installation Manual of the alarm control being used with the unit Before connecting the unit the wires from the electrical box for connection Do use frayed or bent wire Holes alarm C NC C Relay Relay NC C remote LED must have series resistor Please see Do NOT use looped wire under terminals for sys supervision Break the wire run to provide supervision of wiring is completed inspect it and correct any errors applying power to the unit When the wiring has been reviewed neatly insert the wires into the electrical and secure the unit to the mounting plate connect this device use only wiring listed as fit for the pur Mounting Installation the detector on to the base plate using the detector base plate alignment marks Press the detector gently in while rotating the detector clockwise until the detector into place Remove the side tab from the locking tab to in place optional If the side tab is removed to the detector depress tab with a flat blade screwdriver and rotate counter clockwise until the marks up Remove Test Unit test for units without a siren by a magnet near the LED Test Button for greater than 5 Initiate test for units with a siren by pressing the test for greater than 5 seconds activation is indicated by the LED the siren and the reporting to the control panel If the smoke detectors inter connected using model PRM 4W and a detector is then all detectors will sound The detector restores to when the test button is released or when the magnet removed Allow a minimum of 20 seconds between test activa If the detector is in one of the following states when a is initiated it will not enter an alarm state Compensation trouble Failure of heat or smoke detector Other internal faults that could prevent a smoke or heat Smoke sensitivity of installed detectors can be mea without removal or an alarm being generated using the Smoke Detector Test Meter Unit with FSD 100 Smoke Detector Test Meter test the unit using the FSD 100 set the test meter up to devices as per the instructions supplied with the test Depress the test button or place the FSD 100 on outside edge of the plastics beside the test button to acti the reed switch on units without siren on the smoke for 1 second and release If the test button is held for 5 seconds or longer an will be generated Move the test meter over the center the detector wait until you hear the test meter beep the unit and the information can be immediately Please see the instructions supplied with the FSD Smoke Detector Test Meter for more information Compensation Reset replacement of the smoke sensor or other changes change the background signal noise of the detector this the drift compensation be reset Compensation trou is one of the faults indicated when the LED indicator is OFF the siren is chirping Remove power from the unit then press and hold the test for 30 seconds to power down unit Power up unit while pressing the test button The LED will when 5 seconds has elapsed Release the test button 1 second after the fifth LED flash The LED will flash every 8 seconds for 1 minute When the stops flashing test the detector to verify normal Instructions Safety In The Home fires occur in the home and to minimize this danger it is that a household fire safety audit be con and a family escape plan be developed Fire Safety Audit Are all electrical appliances and outlets in safe condition for frayed cords overloaded lighting circuits etc If are uncertain about the condition of your electrical or household service have a professional evalu Are all fl