DSC GS Boost Installation Manual - English

File Preview
File Preview
Click below to download for free

File Data

Name dsc-gs-boost-installation-manual-english-1630724589.pdf
Type PDF
Size 776.95 KB
Downloads

Text Preview

GS BOOST Voltage Booster Instructions DIAGRAM THIS INSTRUCTION SHEET MUST BE USED IN WITH THE GS3060 INSTALLATION MANUAL ADAPTOR side view Rev 02 R1 T1 LINE RNG TIP LINE POWER Use GS BOOST only with DSC GS3060 UA553 Rev 02 information on GS3060 refer to Installation Manual P N 29007442R003 information on Alarm Control Panel refer to its Installation Manual Voltage Yellow Black 9 14VDC Supplied by GS3060 module Current Yellow Black 5mA Normal Standby Condition Input PGM1 White 30mA max Green Red Input Current 22mA max 100mA Communication Condition Telco Loop Specifications TIP RNG Green Red Voltage 22.5 28.5VDC typical 24VDC Current 22 27mA Resistance 350 Ohm max DIAGRAM For UL ULC installa connections between alarm control panel out output relay con and GS3060 Z1 Z4 shall be run a mechanical protective within 20ft 6m of another and in the same O3 O4 OC AS 13 20 12V L1 L2 L3 L4 12V circuits are classified for UL installations as Power Limited Class 2 Power Limited except for the bat leads which are not power limited Do not route any wiring over circuit boards Maintain at least 1 separation A minimum 1 4 6.4mm of separation must be maintained at all points between Limited wiring and all other non Power Limited wiring Route wires as indicated above GS Boost inside the GS3060 enclosure Secure module to enclosure using tie wrap i as indi in this diagram strict accordance with COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Controls could void your authority to use this equipment This generates and uses radio frequency energy and if not installed used properly manufacturer may cause interference to radio and television reception It been type tested and found to comply with the limits for Class B device accordance with the specifications in Subpart B of Part 15 of FCC which are designed to provide reasonable protection against such in any residential installation However there is no guarantee interference will not occur in a particular installation If this equipment cause interference to television or radio reception which can be by turning the equipment off and on the user is encouraged to to correct the interference by one or more of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and are on different circuits necessary the user should consult the dealer or an experienced radio technician for additional suggestions The user may find the booklet prepared by the FCC helpful How to Identify and Radio Television Interference Problems This booklet from the U S Government Printing Office Washington D C Stock 004 000 00345 4 INFORMATION equipment complies with Part 68 of the FCC Rules On the side of equipment is a label that contains among other information the FCC number and ringer equivalence number REN for this If requested this number must be provided to the Telephone Product IdentifierUS F53MO00BGS3060 Jack Connection Requirements plug and jack used to connect this equipment to the premises wiring and network must comply with the applicable FCC Part 68 rules and adopted by the ACTA A compliant telephone cord and plug is provided with this product It is designed to be connected a compatible modular jack that is also compliant See installation for details Equivalence Number REN REN is used to determine the number of devices that may be to a telephone line Excessive RENs on a telephone line may in the devices not ringing in response to an incoming call most but not all areas the sum of RENs should not exceed five 5.0 To certain of the number of devices that may be connected to a line as by the total RENs contact the local Telephone Company For approved after July 23 2001 the REN for this product is part of product identifier that has the format US AAAEQ TXXXX The represented by are the REN without a decimal point e g 03 is a of 0.3 For earlier products the REN is separately shown on the of Harm this equipment GS3060 with GS BOOST causes harm to the telephone the telephone company will notify you in advance that temporary of service may be required But if advance notice is not the Telephone Company will notify the customer as soon as Also you will be advised of your right to file a complaint with FCC if you believe it is necessary in Telephone Company Equipment or Facilities Telephone Company may make changes in its facilities equipment or procedures that could affect the operation of the equipment this happens the Telephone Company will provide advance notice in for you to make necessary modifications to maintain uninterrupted Maintenance Facility trouble is experienced with this equipment for repair or warranty please contact the facility indicated below If the equipment is harm to the telephone network the Telephone Company may that you disconnect the equipment until the problem is solved This is of a type that is not intended to be repaired by the end user c o APL Logistics 757 Douglas Hill Rd Lithia Springs GA 30122 Information to party line service is subject to state tariffs Contact the state utility commission public service commission or corporation for information dialling equipment must be able to seize the telephone line and a call in an emergency situation It must be able to do this even if equipment telephone answering system computer modem etc has the telephone line in use To do so alarm dialling equipment be connected to a properly installed RJ 31X jack that is electrically in with and ahead of all other equipment attached to the same telephone Proper installation is depicted in the figure below If you have any concerning these instructions you should consult your telephone or a qualified installer about installing the RJ 31X jack and alarm equipment for you Premises Equipment and Wiring Dialing Jack Machine Jack CANADA COMPLIANCE STATEMENT Equipment meets applicable Industry Canada Terminal Technical Specifications This is confirmed by the registration The abbreviation IC before the registration number signifies that was performed based on a Declaration of Conformity that Industry Canada technical specifications were met It does imply that that Industry Canada approved the equipment The Ringer Number REN for this terminal equipment is 0.0 The REN to each terminal equipment provides an indication of the number of terminals allowed to be connected to a telephone The termination on an interface may consist of any combination devices subject only to the requirement that the sum of the Ringer Numbers of all devices does not exceed 5 est conforme aux sp techniques applicables terminaux d Canada Ceci est confirm par le d L num signifie que l a

Related Files