DSC HS-CAB1000-CAB3000-CAB4000 - Installation Manual - English

Digital Security Controls Cover Sheet Number Number being packaged and shipped for Medium HS Cab1000 1 Changed all references of HS to HS CAB1000ND 2 other general clean up and regulatory statements Updated part description for HS CAB1000ND logo and DSC info CONCOURSE CABINETS SHEET ENG HS 33 01 8.5 x 11 White Paper 1 Instructions Master Size 8.5 X 11 of Sheets in Master 2 Sided Printing Printing Not Required Not Applicable CABINET shall be installed by SERVICE PERSONS ONLY service person is defined as a per having the appropriate technical training and experience necessary to be aware of haz to which that person may be exposed in performing a task and of measures to minimize risks to that person or other persons is the Installer responsibility to instruct the end user regarding the acceptance for the END of having ACCESS or NOT within the cabinet No ACCESS without the USE of a TOOL be permitted IF within the CABINET IF it is hosting Moving Parts TNV Circuits and or Cir at HAZARDOUS VOLTAGES During the Installation of the DOOR all of the above circuits be DISCONNECTED Warranty Security Controls warrants that for a period of 12 months from the date of purchase the product shall be free of in materials and workmanship under normal use and that in fulfillment of any breach of such warranty Digital Controls shall at its option repair or replace the defective equipment upon return of the equipment to its repair This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or han or damage due to causes beyond the control of Digital Security Controls such as lightning excessive voltage shock water damage or damage arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Digital Controls neither assumes responsibility nor authorizes any other person purporting to act on its behalf to modify to change this warranty nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls be liable for any direct indirect or consequential damages loss of anticipated loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or of this product Digital Security Controls recommends that the entire system be completely tested on a regular basis How despite frequent testing and due to but not limited to criminal tampering or electrical disruption it is possible for product to fail to perform as expected INFORMATION Changes or modifications not expressly approved by Digital Security Controls could the user authority to operate this equipment Compliance Statement Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority use this equipment equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment uses and can radiate radio frequency energy and if not installed and used in accordance with the Instructions may cause interference to radio communications However there is no guarantee that interference will not occur in a particular installa If this equipment does cause harmful interference to radio or television reception which can be determined by turning the on and off the user is encouraged to try to correct the interference by one or more of the following measures Reorient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help user may find the following booklet prepared by the FCC useful to Identify and Resolve Radio Television Interference Prob This booklet is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause interference and 2 this device must accept any interference received including interference that may cause undesired operation 2005 Digital Security Controls Canada cid 127 www dsc com Support 1 800 387 3630 Canada US 905 760 3036 in Canada HS CAB4000 Cabinets Instructions HS CAB1000ND HS CAB3000 HS CAB4000 are DSC Concourse Home Wiring System cabinets specifically designed to house and to protect the Concourse Home Sys telecom data video security audio automation and other modules Large knockouts provided at the top sides and bottom of the cabinets for flexible cable routing There also two single gang electrical knockouts at the bottom of the cabinets The HS HS CAB3000 HS CAB4000 cabinets can either be flush mounted between 16 inch centered studs or surface mounted Raceway cover and hardware shipped with door HS LDR1000 for HS CAB1000ND of Package Cabinet Raceway cover s Hardware pack s Instruction booklet 14.25in 362mm 14.25in 362mm 28.5in 724mm 14.25in 362mm 42in 1067mm 14.25in 362mm Instructions Choose a location where the temperature will not drop below 0 or go above 50 and the humidity will not create condensate on the cabinet or on the installed mod Locating the cabinet in a garage attic or damp basement is not recommended the cabinet in an easily accessed location for service and future upgrades and 2 feet of a 110VAC outlet Alternatively the outlet may be located in the bot of the cabinet using the provided knockout s limitations regarding cabinet locations please consult local electrical and build codes Installation installation between 2 x 4 or larger studs on 16 centers 14.25 opening Remove the slot knock outs on the side of the cabinets Position the cabinet between the studs with the front of the cabinet protruding to level of the finished wall and allowing for front cover installation For example if drywall is to be used extend the cabinet at least 5 8 past the studs Hold the in place and mark the position of the center of the slots Set the cabinet down and drill pilot holes for the mounting screws Place the cabinet in position and secure with the screws 6 x pan head wood not supplied Remove knockouts as required and install cable protection grommets in the holes Installation installation will be on plywood backboard a plywood backboard to the wall studs using three 10 x 2 wood screws supplied per side Allow sufficient clearance for the cabinet and access to the Position the cabinet at a suitable height and mark the location of the upper mount holes Set the cabinet down and drill pilot holes for the upper mounting screws the upper mounting screws 6 x pan head wood screws not supplied do not fully tighten Hang the cabinet on the upper mounting screws mark the knockout holes and the and bottom mounting screw locations Remove the cabinet and cut the cable access holes in the plywood removing any edges cable protection grommets not supplied in the holes in the back of the cabinet Hang the cabinet on the upper mounting screws install the center and bottom screws 6 x pan head wood screws not supplied and tighten the mounting screws Remove other knockouts as required and install cable protection grommets not sup in the holes Instructions cables are low voltage or communications cables Observe good wiring practices and according to appropriate wiring codes Maintain proper separation of these cables 110 220VAC power cables and use proper cable management and labeling techniques all cables into the cabinet through the raceway Allow sufficient length at both of the run to avoid stress and for proper termination and trim out Label each cable both ends for easier identification and secu