DSC HS-DH400 - Installation Manual - English - Concourse 4-Port Patch Panel

FCC COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your to use this equipment equipment has been tested and found to comply with the limits for a Class B digital device pursuant to 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfer in a residential installation This equipment generates uses and can radiate radio frequency energy and not installed and used in accordance with the instructions may cause harmful interference to radio commu However there is no guarantee that interference will not occur in a particular installation If this does cause harmful interference to radio or television reception which can be determined by turn the equipment off and on the user is encouraged to try to correct the interference by one or more of the fol measures the receiving antenna the separation between the equipment and receiver the equipment into an outlet on a circuit different from that to which the receiver is connected the dealer or an experienced radio television technician for help user may find the following booklet prepared by the FCC useful to Identify and Resolve Radio Tele Interference Problems This booklet is available from the U S Government Printing Office Washington 20402 Stock 004 000 00345 4 Security Controls Ltd warrants that for a period of 12 months from the date of purchase the product shall be free defects in materials and workmanship under normal use and that in fulfillment of any breach of such warranty Digital Controls Ltd shall at its option repair or replace the defective equipment upon return of the equipment to its depot This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or or damage due to causes beyond the control of Digital Security Controls Ltd such as lightning excessive volt mechanical shock water damage or damage arising out of abuse alteration or improper application of the equip foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd Digital Controls Ltd neither assumes nor authorizes any other person purporting to act on its behalf to modify or to this warranty nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss of antici profits loss of time or any other losses incurred by the buyer in connection with the purchase installation or opera or failure of this product Digital Security Controls Ltd recommends that the entire system be completely tested on a regular basis despite frequent testing and due to but not limited to criminal tampering or electrical disruption it is possible this product to fail to perform as expected INFORMATION Changes or modifications not expressly approved by Digital Security Controls Ltd void the user authority to operate this equipment Port Patch Panel Instructions HS DH400 4 Port Patch panel is intended to facilitate the interconnection of cabling in the DSC Concourse Home System This module can be in Concourse Home Systems cabinets HS CAB1000 HS CAB3000 and using the supplied mounting hardware 1 HS DH400 Bracket with toolless RJ45 outlet jacks Digital Security Controls Ltd Canada www dsc com Printed in Canada of Package installing this module verify that the package contains the following Qty 1 HS DH400 metal bracket Qty 1 Hardware pack containing two phillips flathead screws Qty 4 Toolless RJ45 outlet jacks Qty 2 Installation Instructions Align and snap the toolless jacks in bracket Locate a suitable mounting location for the HS DH400 Ethernet Hub inside cabinet Note that the unit can be installed in various positions the jacks may face the top or the bottom of the cabinet Align the two mounting pins with the holes in the back of the cabinet and as per Figure 2 Snap the module in place by pressing both sides towards the back of the Secure the metal bracket to the cabinet using the two screws With the plate in position cut the CAT 5 cable to the appropriate length Follow the instructions for the Outlet Jack for correct installation 2 Installation following requirements for installation of CAT5 cable must be met for operation of connected equipment Do NOT strip off cable sheathing more than required for proper Do NOT kink or knot cable Do NOT crush cable with cable ties Do NOT splice cable Do NOT bend cable at right angles or make any other sharp bends All bends must have a minimum of a 2 radius Do NOT untwist CAT5 pairs more than HS CAB3000 HS CAB4000 cabinet jack upward until slot snaps in place Toolless outlet jack slot in bracket