DSC HS-MP - Installation Manuals - English - Concourse Mounting Plate

Wiring Instructions the wiring instruction included with the Concourse Power or Maxsys module 4 x 6 Accommodated not limited to Concourse HS NH400 HS AH600 HS DH800 Security PC500 PC510 PC550 PC560 PC580 PC1555 PC1565 PC5008 PC5204 PC5208 PC5400 PC5401 PC5700 PC5720 PC4108 PC4216 PC4400 Escort4580 Escort5580 Escort5580TC Links 2150 RL 4LC PS3085 8 x 6 Accommodated not limited to Concourse none PC5108L PC5010 PC5020 PC5908 PC5928 PC4204 PC4216 PC4702 SN4204 DLM 4 12 x 6 Accommodated not limited to Concourse none PC4020 PC4020A PC4030A Security Controls Ltd warrants that for a period of 12 months from the date of purchase the product shall be free of defects in and workmanship under normal use and that in fulfilment of any breach of such warranty Digital Security Controls Ltd shall at its repair or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in and workmanship and not to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Security Ltd such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether expressed or and of all other obligations or liabilities on the part of Digital Security Controls Ltd Digital Security Controls Ltd neither assumes nor any other person purporting to act on its behalf to modify or to change this warranty nor to assume for it any other warranty or concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss of anticipated loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure this product detectors can only detect motion within the designated areas as shown in their respective installation instructions They discriminate between intruders and intended occupants Motion detectors do not provide volumetric area protection They multiple beams of detection and motion can only be detected in unobstructed areas covered by these beams They cannot motion which occurs behind walls ceilings floor closed doors glass partitions glass doors or windows Any type of whether intentional or unintentional such as masking painting or spraying of any material on the lenses mirrors or any other part of the detection system will impair its proper operation infrared motion detectors operate by sensing changes in temperature However their effectiveness can be reduced when the ambient rises near or above body temperature or if there are intentional or unintentional sources of heat in or near the detection area of these heat sources could be heaters radiators stoves barbeques fireplaces sunlight steam vents lighting and so on Digital Security Controls Ltd recommends that the entire system be completely tested on a regular basis However frequent testing and due to but not limited to criminal tampering or electrical disruption it is possible for this product fail to perform as expected INFORMATION Changes or modifications not expressly approved by Digital Security Controls Ltd could the user authority to operate this equipment Digital Security Controls Ltd Canada 1 800 387 3630 www dsc com in Canada 29005201 R001 Series Plate Instructions HS MP series of mounting plates are for use with the DSC Concourse Home modules and DSC Power and Maxsys security system products The Concourse and kits include the mounting plates To install DSC security products in cabinets one of these plates is required A wide variety of Power and Maxsys can be accommodated by the three plate sizes of Package package contains the following parts Four HS MP200 small plates or Two HS MP300 medium plates or One HS MP400 large plate Instructions Insert the standoffs not supplied into the mounting plate as per Figure A matching hole pattern on the Concourse Power or Maxsys module to be installed Mounting Plate A Align the module over the standoffs and snap into place Locate a suitable mounting location for the module inside the cabinet Align the two mounting tabs with the holes in wire raceway and insert as per Figure B Snap the module into place by pushing the opposite side towards the back of the cabinet B Instructions the wiring instruction included with the Concourse Power or Maxsys module 4 x 6 Accommodated not limited to Concourse HS NH400 HS AH600 HS DH800 Security PC500 PC510 PC550 PC560 PC580 PC1555 PC1565 PC5008 PC5204 PC5208 PC5400 PC5401 PC5700 PC5720 PC4108 PC4216 PC4400 Escort4580 Escort5580 Escort5580TC Links 2150 RL 4LC PS3085 8 x 6 Accommodated not limited to Concourse none PC5108L PC5010 PC5020 PC5908 PC5928 PC4204 PC4216 PC4702 SN4204 DLM 4 12 x 6 Accommodated not limited to Concourse none PC4020 PC4020A PC4030A Security Controls Ltd warrants that for a period of 12 months from the date of purchase the product shall be free of defects in and workmanship under normal use and that in fulfilment of any breach of such warranty Digital Security Controls Ltd shall at its repair or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in and workmanship and not to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Security Ltd such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether expressed or and of all other obligations or liabilities on the part of Digital Security Controls Ltd Digital Security Controls Ltd neither assumes nor any other person purporting to act on its behalf to modify or to change this warranty nor to assume for it any other warranty or concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss of anticipated loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure this product detectors can only detect motion within the designated areas as shown in their respective installation instructions They discriminate between intruders and intended occupants Motion detectors do not provide volumetric area protection They multiple beams of detection and motion can only be detected in unobstructed areas covered by these beams They cannot motion which occurs behind walls ceilings floor closed doors glass partitions glass doors or windows Any type of whether intentional or unintentional such as masking painting or spraying of any material on the lenses mirrors or any other part of the detection system will impair its proper operation infrared motion detectors operate by sensing changes in temperature However their effectiveness can be reduced when the ambient rises near or above body temperature or if there are intentional or unintentional sources of heat in or near the detection area of these heat sources could be heaters radiators stoves barbeques fireplaces sunlight steam vents lighting and so on Digital Security Controls Ltd recommends that the entire system be completely tested on a regular basis However frequent testing and due to but not limited to criminal tampering or electrical disruption it is possible for this product fail to perform as expected INFORMATION Changes or modifications not expressly appr