DSC HS-VH1802DSS - Installation Manual - English - Concourse Passive 1x8 Video Splitter with Dual Low-Noise Blocking Pass-Through Connectors

File Preview
File Preview
Click below to download for free

Text Preview

Warranty Security Controls Ltd warrants that for a period of 12 months from the date of purchase the product shall be free defects in materials and workmanship under normal use and that in fulfillment of any breach of such warranty Digital Controls Ltd shall at its option repair or replace the defective equipment upon return of the equipment to its depot This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or or damage due to causes beyond the control of Digital Security Controls Ltd such as lightning excessive volt mechanical shock water damage or damage arising out of abuse alteration or improper application of the equip foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd Digital Controls Ltd neither assumes responsibility for nor authorizes any other person purporting to act on its behalf to or to change this warranty nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss of antici profits loss of time or any other losses incurred by the buyer in connection with the purchase installation or opera or failure of this product Digital Security Controls Ltd recommends that the entire system be completely tested on a regular basis despite frequent testing and due to but not limited to criminal tampering or electrical disruption it is possible this product to fail to perform as expected INFORMATION Changes or modifications not expressly approved by Digital Security Controls Ltd void the user authority to operate this equipment Compliance Statement Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to use this equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment uses and can radiate radio frequency energy and if not installed and used in accordance with the Instructions may cause interference to radio communications However there is no guarantee that interference will not occur in a particular installa If this equipment does cause harmful interference to radio or television reception which can be determined by turning the on and off the user is encouraged to try to correct the interference by one or more of the following measures the receiving antenna the separation between the equipment and receiver the equipment into an outlet on a circuit different from that to which the receiver is connected the dealer or an experienced radio TV technician for help user may find the following booklet prepared by the FCC useful to Identify and Resolve Radio Television Interference Prob This booklet is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not harmful interference and 2 this device must accept any interference received including interference that may cause undes operation Home Systems is a division of Digital Security Controls Ltd Digital Security Controls Ltd Canada www dsc com in Canada 29034469 R001 Passive Video Module Dual LNB DSS Connections Instructions HS VH1802DSS is a 1 x 8 passive video module combined with DSS dual LNB connections on the same mounting plate for use with the DSC Con Home Wiring Systems Solution The passive video module is all ports power APP with one CATV ANT input and eight outputs for multi room video sig distribution The passive video module can also be used as an 8 input to one out video combiner The DSS pass through connections provide a convenient interface a satellite dish and two receivers All connectors use style fittings of Package 1 Splitter x 8 Video Module and dual LNB pass throughs on a mounting plate MHz 40 400 600 1000 Loss dB max dB max dB max dB max P to P dB min dB min dB min dB min dB min dB min dB min dB min Loss Shielding Ohm dB Passing ports 24VDC 500 mA DSS Connections MHz Loss dB max Instructions Select a suitable mounting location for the HS VH1802DSS module inside the cabi The upper left corner of the cabinet is recommended Align the mounting tabs with the slots in the wire raceway and insert See Figure 1 Snap the module into place by pushing the opposite side towards the back of the requirements for installation of coaxial cable should be met for proper operation of connected Do not strip off cable sheathing more than required for proper termination Do not kink or cable Do not crush cable with cable ties Do not bend cable at right angles or create any other bends All cable bends should have a minimum of a 2 radius Attach RG6 style connectors to the incoming CATV ANT service and internal video cables Connect the terminated incoming service and internal mod cables to the red terminals on the passive video module Make up an RG6 patch cord of sufficient length to connect the red terminal of HS VH1802DSS to the black terminal of the HS VH400 or HS VH1800 or the terminal of the HS VA800 All drops to outlets will terminate at the terminals of the HS VH400 or HS VH1800 or at the white of the HS VA800 Terminate any unused terminals with a 75 Ohm terminator Test all connections to confirm proper installation and termination Instructions Incoming Service Cable Route the incoming service cables into the cabinet through the raceway to the HS Module Allow sufficient length at both ends of the run to avoid stress for termination and trim out Attach an RG6 style connector to each incoming service cable Connect the ter incoming service cable to the black terminal on the passive video mod and at the DSS fittings as appropriate Test all connections to confirm proper installation and termination Outlet Cables Home run RG6 coax cable to each desired outlet location and route the cables into cabinet through the raceway to the HS VH1802DSS module Allow sufficient at both ends of the run to avoid stress and for proper termination and trim Label each cable run at both ends for easier identification Terminate each RG6 drop at the desired outlet location using an RG6 style Attach the connector to an RG6 style jack and trim out using the wall plate If using a multiple outlet wall plate mark the jack accordingly Terminate each RG6 drop at the HS VH1802DSS module using an RG6 style con Connect the terminated drops to the black terminals and at the DSS as appropriate Terminate any unused terminals with a 75 Ohm terminator Test all connections to confirm proper installation and termination Video Module as Combiner used with an HS VH400 an HS VH1800 or an HS VA800 video module or other video module the passive splitter of the HS VH1802DSS can be used to com and distribute external CATV ANT and internal e g CCTV video signals Route the incoming CATV ANT service cable s into the cabinet through the raceway the HS VH1802DSS Allow sufficient length at both ends of the run to avoid stress for proper termination and trim out Route the incoming modulated internal video cable s into the cabinet through the to the HS VH1802DSS module Allow sufficient length at both ends of the to avoid stress and for proper termination and trim out

Related Files