DSC Install Instructions PC5208 v1-0 - En - Rev4
File Preview
Click below to download for free
Click below to download for free
File Data
Name | dsc-install-instructions-pc5208-v1-0-en-rev4-3670819542.pdf |
---|---|
Type | |
Size | 1.12 MB |
Downloads |
Text Preview
PC5208 v1.0 Installation Instructions Low Current Output Module installation sheet shall be used in conjunction with the Installation Manual of the DSC equipment to the PC5208 is connected e g alarm controller power supply etc PC5208 module can be used to add up to 8 low current programmable outputs to the compatible Alarm Controllers models PC5010 PC5015 PC5020 PC1864 PC1832 and PC1616 product meets the requirements of Class II Grade 2 equipment as per EN50131 1 2006 A1 2009 Type A Standard Temperature range 10 to 55 Relative Humidity 93 non condensing Input ratings 12VDC 700mA provided by the alarm controller or separate limited power supply Board current draw 20mA set and unset state alarm and non alarm state Board dimensions 45mm x 92mm AUX output ratings 12VDC 15 15 when Input voltage is between 85 to110 of rated value output current is between 0mA 250mA max PGM outputs Open collector switched to ground 50mA max Resettable fuse PTC used on circuit board instead of replaceable fuses There are no serviceable Descriptions This can be used to tamper the cabinet in which the PC5208 is mounted Connect a normally NC switch across TAM and BLK If the tamper is not being used connect a piece of wire across and BLK to remove the trouble condition There is a built in tamper switch on the expander module located in the top left corner of circuit board If the cabinet used to mount the PC5208 Output Module has the hardware to depress this tamper switch then DO NOT connect anything to the TAM terminal There are two terminals for AUX power to provide easier wiring These terminals are used to power for devices Maximum current draw is not to exceed 250 mA Connect the positive lead of devices to either AUX and the negative to the proper output terminal O1 to O8 The 4 wire KEYBUS connection is used by the panel to communicate with the module Con the RED BLK YEL and GRN terminals to the KEYBUS terminals on the main control to O8 Wire the positive lead of the device to either AUX terminal and the negative lead to the output terminal O1 to O8 The following are examples of how to wire various devices to the PC5208 may be installed within the same metallic cabinet as the alarm controller power supply Power UC1 PC5003C or in a separate enclosure model PC4003C Internal and or external for this module shall be routed supported clamped or secured in a manner that reduces the like of excessive strain on wire and on terminal connections loosening of terminal connections and of conductor insulation PC5208 can be installed in the metal enclosures listed below Tamper protection switches can be on all enclosures including door opening protection and or removal from the mounting posi Doors can be secured using screws or keylock Model PC5003C removable door made of 22Ga steel painted dimensions 248mm L x Model PC5003C hinged door made of 1.2mm thick steel painted dimensions 248mm L x x 76mm H weight 1500g x 76mm H weight 2500g Model Power UC1 made of 18Ga steel painted dimensions 315mm L x 319mm W x 100mm H 3150g 1050g Model PC4003C made of 18Ga steel painted dimensions 230mm L x 180mm W x 75mm D The Model PC5208 Output Module has been certified by Telefication according to A1 2009 for Grade 2 Class II when installed in the PC5003C removable enclosure WARRANTY Security Controls DSC warrants that for a period of twelve months from the date of purchase the product shall be free of in materials and workmanship under normal use and that in fulfillment of any breach of such warranty DSC shall at its option or replace the defective equipment upon return of the equipment to its factory This warranty applies only to defects in parts and and not to damage incurred in shipping or handling or damage due to causes beyond the control of DSC such as light excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper application of the foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether or implied and of all other obligations or liabilities on the part of DSC This warranty contains the entire warranty Digital Controls neither assumes responsibility for nor authorizes any other person purporting to act on its behalf to modify or to this warranty nor to assume for it any other warranty or liability concerning this product In no event shall DSC be liable for any or indirect or consequential damages loss of anticipated profits loss of time or any other losses incurred by the buyer in connec with the purchase installation or operation or failure of this product Digital Security Controls recommends that the entire system be completely tested on a regular basis However despite fre testing and due to but not limited to criminal tampering or electrical disruption it is possible for this product to fail to per as expected COMPLIANCE STATEMENT Changes or modifications not expressly approved by DSC could void your authority to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the manufac instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits Class B device in accordance with the specifications in Subpart of Part 15 of FCC Rules which are designed to provide reason protection against such interference in any residential installation However there is no guarantee that interference will not occur a particular installation If this equipment does cause interference to television or radio reception which can be determined by turn the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may the following booklet prepared by the FCC useful to Identify and Resolve Radio Television Interference Problems This is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 READ CAREFULLY DSC SOFTWARE PURCHASED WITH OR WITHOUT PRODUCTS AND COM IS COPYRIGHTED AND IS PURCHASED UNDER THE FOLLOWING LICENSE TERMS End User License Agreement is a legal agreement between You the company individual or entity who acquired the Software and any Hardware and Digital Security Controls a division of Tyco Safety Products Canada Ltd the manufacturer of the integrated security and the developer of the software and any related products or components which You acquired If the DSC software prod PRODUCT or is intended to be accompanied by HARDWARE and is NOT accompanied by new HARDWARE You not use copy or install the SOFTWARE PRODUCT The SOFTWARE PRODUCT includes computer software and may include associated media materials and or electronic documentation Any software provided along with the SOFTWARE PRODUCT that is associated with a end user license agreement is licensed to You under the terms of that license agreement installing copying downloading storing accessing or otherwise using the SOFTWARE PRODUCT You agree unconditionally to be bound by the of this EULA even if this EULA is deemed to be a modification of any previous arrangement or contract If You do not agree to the terms of this DSC is unwilling to license the SOFTWARE PRODUCT to You and You have no right to use it PRODUCT LICENSE SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties as well as other intellectual property laws and treaties SOFTWARE PRODUCT is licensed not sold GRANT OF LICENSE This EULA grants You the following rights Software Installation and Use For each license You acquire You may have only one copy of the SOFTWARE PRODUCT installed Storage Network Use The SOFTWARE PRODUCT may not be installed accessed displayed run shared or used concurrently on or from differ computers including a workstation terminal or other digital electronic device In other words if You have several workstations You have to acquire a license for each workstation where the SOFTWARE will be used Backup Copy You may make back up copies of the SOFTWARE PRODUCT but You may o