DSC IT-230 RS-422 Interface Module Installation Manual

IT 230 Module This manual contains information on limitations regarding product use and and information on the limitations as to liability of the manufacturer Manual OF CONTENTS to Installers 2 3 3 3 3 Interface Pre Installation Configuration 4 the RS 422 Cable 4 Factory Default 4 the IT 230 with Panel 4 Connection between IT 230 and Panel 5 Connection for C24 HUB 5 Panel Programming 6 Data Display 6 HEX values at keypad 6 ASCII Characters at keypad 6 Initial Programming 6 PROGRAMMING SECTION 7 Options 7 Options 7 Zone Lifestyle Toggle Options 8 Zone Notification Toggle Options 9 Information Read Only 10 Reset Defaults 10 WORKSHEET 11 Options 11 Options 11 Zone Lifestyle Toggle Options 11 Zone Notification Toggle Options 11 Information Read Only 11 Reset Defaults 11 Please Read Carefully to Installers Warning contains vital information As the only individual in contact with system users it is the installer responsibility to bring each item in this Warning to the attention of all users of this system Failures system has been carefully designed to be as effective possible There are circumstances however involving burglary or other types of emergencies where it may provide protection Any alarm system of any type may compromised deliberately or may fail to operate as for a variety of reasons Some but not all of these may be by Intruders may enter through an unprotected access point a sensing device evade detection by moving an area of insufficient coverage disconnect a warn device or interfere with or prevent the proper operation the system Failure every effort has been made to make this system reliable as possible the system may fail to function as due to the failure of a component of Radio Frequency Wireless Devices may not reach the receiver under all circumstances could include metal objects placed on or near the path or deliberate jamming or other inadvertent radio interference Knowledge system contains security features which were known to effective at the time of manufacture It is possible for per with criminal intent to develop techniques which the effectiveness of these features It is important your security system be reviewed periodically to ensure its features remain effective and that it is updated or if it is found that it does not provide the protection of Replaceable Batteries system wireless transmitters have been designed to several years of battery life under normal condi The expected battery life is a function of the device usage and type Ambient conditions such as humidity high or low temperatures or large tempera fluctuations may reduce the expected battery life While transmitting device has a low battery monitor which when the batteries need to be replaced this moni may fail to operate as expected Regular testing and will keep the system in good operating condi Installation security system must be installed properly in order to pro adequate protection Every installation should be eval by a security professional to ensure that all access and areas are covered Locks and latches on win and doors must be secure and operate as intended doors walls ceilings and other building materials be of sufficient strength and construction to provide level of protection expected A reevaluation must be during and after any construction activity An evalua by the fire and or police department is highly recom if this service is available Testing problems that would prevent an alarm system from as intended can be found by regular testing and The complete system should be tested and immediately after a break in an attempted a fire a storm an earthquake an accident or any of construction activity inside or outside the premises testing should include all sensing devices keypads alarm indicating devices and any other opera devices that are part of the system Time may be circumstances when the system will operate intended yet the occupants will not be protected from an due to their inability to respond to the warnings a timely manner If the system is remotely monitored the may not occur in time to protect the occupants or belongings Detectors detectors can only detect motion within the desig areas as shown in their respective installation instruc They cannot discriminate between intruders and occupants Motion detectors do not provide volu area protection They have multiple beams of detec and motion can only be detected in unobstructed areas by these beams They cannot detect motion which behind walls ceilings floor closed doors glass par glass doors or windows Any type of tampering intentional or unintentional such as masking paint or spraying of any material on the lenses mirrors win or any other part of the detection system will impair its operation infrared motion detectors operate by sensing in temperature However their effectiveness can reduced when the ambient temperature rises near or body temperature or if there are intentional or unin sources of heat in or near the detection area of these heat sources could be heaters radiators barbeques fireplaces sunlight steam vents light and so on Failure units intrusion detectors smoke detectors and other security devices require an adequate power for proper operation If a device operates from bat it is possible for the batteries to fail Even if the bat have not failed they must be charged in good and installed correctly If a device operates only by