DSC LCD5501Z v2 1 - Installation Manual - Trilingual - PowerSeries Fixed-Message LCD Keypad

LCD55O1Z 2.1 Instructions d de Instalacion Please refer to the System Installation Manual for information on limitations product use and function and information on the limitations as to liability of the Ce manuel contient des informations sur les restrictions concernant le et l du produit et des informations sur les restrictions en ce qui la responsabilit du fabricant La totalit du manuel doit lu attentivement Este manual contiene informaci sobre restricciones acerca del y funcionamiento del producto e informaci sobre las limitaciones tal como la re del fabricante Todo el manual se debe leer cuidadosamente of Contents Table des Matieres Contenido 1 1 1 1 1 Power 2 2 the Keypad the Keypad 2 Key Options 3 Options 3 Displayed While Armed Option 3 Key Options Auxiliary Panic 3 Chime Options Chime on Zone Openings Closings 4 Chime Sounds 4 Input PGM Output Option the PGM Number 4 Worksheets Door Chime Sound Programming 6 11 11 sous tension 12 du clavier du clavier pour les touches de fonction 13 pour l 13 d des alarmes le syst est arm pour les touches d auxiliaire et panique 14 pour le carillon de porte de porte lors de l des zones 14 pour le carillon 15 pour la borne de zone sortie PGM du num de la PGM 15 de programmation le carillon de porte Programmation de la tonalit 22 Energ 23 el Teclado el Teclado de las Teclas Funcionales 24 del Reloj 24 Alarmas Mostradas Armado 24 de Teclas de Emergencia Auxiliar P 24 del Timbre de Puerta de Puerta en Cierres Aperturas Zonas 25 del Timbre de Puerta 25 de Entrada de PGM del n de PGM 26 de Programaci 27 de Puerta Programar el Sonido del exit Once you have selected a dry secure location perform the follow steps to mount the keypad LCD5501Z keypad presents system using an LCD display along with words icons and numbers The key can be used on security systems up to 64 zones The LCD5501Z is with the following DSC secu systems PC580 PC585 PC5008 PC1555 PC1565 cid 127 PC50XX PC1555MX Connects to control panel via 4 wire One keypad zone input PGM output Current draw 35mA standby maximum Voltage rating 12VDC nominal Optional tamper version Five programmable function keys Ready green Armed red and Trou yellow status lights LCD5501Z package includes the fol parts One LCD5501Z keypad Four mounting screws One keypad inner door label One set of Fire Auxiliary and Panic labels should mount the keypad where it is to designated points of entry SYSTEM WEEKLY to Instruction Manual for instructions IN USEXXNOT IN USE IN USE Remove the keypad backplate by the screw located at the of the unit the keypad backplate to the in the desired location Use the provided Before attaching the keypad to its complete the keypad wir as described in the next section Before beginning to wire the unit en that all power AC transformer battery is disconnected from the panel Connect the four Keybus wires from control panel red black yellow green to the keypad terminals R Y G Consult the diagram below Y G Z P Blk Yel Grn To Zone Input Output programmed as an input you can a device such as a door to the terminal of the This eliminates the need to wires back to the control panel for device To connect the zone run wire from the device to the and the other wire from the to the B black terminal For devices run the red wire to R positive terminal and the black to the B negative terminal When end of line supervision connect zone according to one of the con outlined in your system Manual the terminal is programmed as output the output follows the PGM in Section 8 A small re buzzer or other DC operated de may be connected between the supply voltage and the maximum load is 50mA Power all wiring is complete apply power the control panel Connect the battery leads to the battery Connect the AC transformer more information on control panel specifications see the control Installation Manual Do not connect the power until all wir is complete the Keypad all wiring is complete you will need enter a 2 digit number that tells the the partition and slot assignment the keypad your system has partitions you will to also assign the keypad to a par 1st digit slot assignment 2nd digit tells the which keypad slots are occupied panel can then generate a fault when keypad supervisory signal not There are eight available slots keypads LCD5501Z keypads are al assigned to slot 1 by default You need to assign each keypad to its slot 1 to 8 the following at each keypad in on the system Installer Programming by press 8 Installer Code 000 for Keypad Programming 0 for Partition and Slot Assign a two digit number to specify the and slot assignment If your system does not have partitions 1 for the first digit digit Enter 0 for Global Keypad 1 for Partition 1 Keypad 2 for Partition 2 Keypad 3 for Partition 3 Keypad 4 for Partition 4 Keypad 5 for Partition 5 Keypad 6 for Partition 6 Keypad 7 for Partition 7 Keypad 8 for Partition 8 Keypad digit Enter 1 to 8 for Slot Assignment the key twice to exit pro After assigning all keypads perform a reset by entering 8 In Code 902 The panel will supervise all assigned keypads enrolled modules on the system the Keypad are several programming options LCD5501Z keypad are described below Record all programming choices in the pro worksheets included in this the LCD5501Z is similar to the rest of the system you are in the LCD5501Z program sections the keypad will display options are turned on along the top the display To turn an option on or off the number corresponding to the on the number pad The numbers the options that are currently turned will be displayed example if options 1 and 2 are on display will look like information on programming the rest your security s