DSC LCD5501Z32-433T - Operation Manual - English - PowerSeries Maxsys Envoy Wireless Tester

FCC COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accor with the manufacturer instructions may cause interference to radio and television reception It has been type and found to comply with the limits for Class B device in accordance with the specifications in Subpart of 15 of FCC Rules which are designed to provide reasonable protection against such interference in any residen installation However there is no guarantee that interference will not occur in a particular installation If this does cause interference to television or radio reception which can be determined by turning the equip off and on the user is encouraged to try to correct the interference by one or more of the following measures the receiving antenna the alarm control with respect to the receiver the alarm control away from the receiver the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional sugges The user may find the following booklet prepared by the FCC helpful to Identify and Resolve Radio Interference Problems This booklet is available from the U S Government Printing Office Washing D C 20402 Stock 004 000 00345 4 Canada COMPLIANCE STATEMENT Class B digital apparatus meets all requirements of the Canadian interference causing equipment regulations appareil num de la Classe B respecte toutes les exigences de r sur le mat brouilleur du Warranty warrants that for a period of one year from the date of purchase the product shall be free of defects in material workmanship under normal use and that in fulfillment of any breach of such warranty DSC shall at its option or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only defects in materials and workmanship and not to damage incurred in shipping or handling or damage due to beyond the control of DSC such as lightning excessive voltage mechanical shock water damage or damage out of abuse alteration or improper application of the product foregoing warranty shall apply only to the original purchaser and shall be in lieu of any and all other warranties expressed or implied and of all other obligations or liabilities on the part of DSC This warranty contains the warranty DSC neither assumes responsibility for nor authorizes any other person purporting to act on its to modify or to change this warranty nor assume for it any other warranty or liability concerning this product no event shall DSC be liable for any direct indirect or consequential damages loss of anticipated profits loss of or any other losses incurred by the purchaser in connection with the purchase installation or operation or of this product results are only valid at the time of testing Results may vary with but are not limited to environmental structural changes Electrical equipment operating in the immediate area may cause interference Digital Security Controls Ltd Canada cid 127 1 800 387 3630 cid 127 www dsc com in Canada 29005977 R001 NA Diagnostic Tester Guide NA Digital Tester Modes RF Jam Detect press 1 Module Placement press 2 Keys Toggle to View SN M2 SN Filter Programming M2 F4 F5 P1 to P3 cid 127 For Future Use In Mode 1 In Mode 2 Icons Serial Number Good Result Bad Result Low Battery Scroll Display Backward Scroll Display Forward Transmissions in Memory Programming Mode 1st and 2nd Digits of the SN 3rd and 4th Digits of the SN 5th and 6th Digits of the SN battery before use see page 5 that the unit is turned OFF after use to avoid battery This document contains information on limitations regarding use and function and information on the limitations as to liability the manufacturer Read the entire manually carefully of Contents of Contents 1 2 2 of the Box 2 Indicators 1 Ready Mode 3 1 RF Jam Detect Test 3 2 Module Placement Test 4 4 Scrolling 4 Number View 4 Number Filter Programming 5 Installation Charging 5 of Illustrations 1 Controls Indicators 1 2 Battery Installation 5 of Tables 1 Key Functions 2 Number Filter Programming Serial Number Filter programming section allows the user to manually program a serial to use as a filter To program the serial number filter press the F3 key This section has a of 000000 programmed by default which disables the serial number filter with the result the unit will use all data from received RF transmissions in the selected test If the user a specific serial number in this location other than 000000 then the unit will only use from that particular device for the selected test This option only applies to mode 2 to Table 1 for key functions Installation Charging 2 Battery Installation 2 Module Placement Test module placement test is used to evaluate the quality of placement of the RF devices This can be performed with the transmitter provided or with in place wireless detectors See Number Filter Programming on page 5 testing existing wireless devices the unit will count the number of received RF transmis for a single event and give a good or bad result for each The unit has an event that can store up to 32 status open close transmissions When the test is in progress unit will give real time or results The user ends the test by pressing either the or keys Exiting mode 2 will clear the event memory mode 2 the tester counts the number of received event transmis from a device and displays the result Using the constant signal transmitter provided the LCD5501Z32 433T will ONLY count status open close transmissions for the placement result Supervi that are sent at one second intervals are ignored batteries in the WLS925L 433 the LCD5501Z32 433T at the intended location of the receiver the transmitter at the intended location of the wireless detector the reed switch with the magnet see WLS925L 433 Installation for location of the reed switch F1 to toggle to Serial Number View menu for current event LCD5501Z32 433T will give one result for each time the magnet is and removed from the reed switch The result may take up to 5 to be annunciated Scrolling the test has ended the number of the most recent event 01 to 32 will appear on the dis The user is now able to scroll forward and backward through the events using the and Event Scroll menu functions in mode 2 while Event Scrolling is active Scroll back one event Scroll forward one event Return to Ready mode to Serial Number View menu for current event Number View serial number of the device that caused the event can be viewed by scrolling to the desired number then pressing the F1 key In the Serial Number View menu the icon will at the top of the display indicating that the serial number is being displayed The serial digit places currently being viewed will be displayed to the right of