DSC LCD5511 v1 0 - Installation Manual - Trilingual - PowerSeries ICON LCD Keypad

LCD5511 1 O Instructions d de Instalacion Please refer to the System Installation Manual for information on limitations product use and function and information on the limitations as to liability of the Ce manuel contient des informations sur les restrictions concernant le et l du produit et des informations sur les restrictions en ce qui la responsabilit du fabricant La totalit du manuel doit lu attentivement Este manual contiene informaci sobre restricciones acerca del y funcionamiento del producto e informaci sobre las limitaciones tal como la re del fabricante Todo el manual se debe leer cuidadosamente Four mounting screws one end of line resistor three keypad inner door labels one tamper switch surface tape one user Instruction Manual one Installation Manual should mount the keypad where it is to designated points of entry exit Once you have selected a dry secure location perform the follow steps to mount the keypad Remove the keypad backplate by the screw optional located the base of the unit Secure the keypad backplate to the in the desired location Use the provided To use the keypad tamper insert the switch supplied into the opening in the centre of the backplate For tamper use try to ensure the back is mounted on a smooth flat sur If mounting on a rough surface the enclosed surface tape to wall to even out the surface area the tamper will be positioned Before attaching the keypad to its complete the keypad wir as described in the next section Before wiring the unit ensure that all AC transformer and battery is from the control panel Connect the four Keybus wires from control panel red black yellow green to the keypad terminals R Y G Consult the diagram below Y G Z P BLK YEL GRN To Zone Input Output LCD5511 keypad presents system using an LCD display along with and numbers The keypad can used on security systems with up to zones The LCD5511 is compatible the following DSC security systems PC580 PC585 PC5008 PC1555 PC1565 cid 127 PC50XX Voltage rating 12VDC nominal Connects to control panel via 4 wire One keypad zone input PGM output Current draw 22mA standby 85mA Optional tamper version Four programmable function keys Ready green and Armed red status Low temperature sensor LCD5511 package includes the fol parts One LCD5511 keypad If programmed as an input you can a device such as a door to the terminal of the This eliminates the need to wires back to the control panel for device To connect the zone run wire from the device to the and the other wire from the to the B black terminal For devices run the red wire to R positive terminal and the black to the B negative terminal When end of line supervision connect zone according to one of the con outlined in your system Manual If the terminal is programmed as output the output follows the PGM in Section 000 8 A relay buzzer or other DC operat device may be connected between positive supply voltage and the terminal maximum load is 50mA Power all wiring is complete apply power the control panel Connect the battery leads to the battery Connect the AC transformer more information on control panel specifications see the control Installation Manual Do not connect the power until all wir is complete the Keypad all wiring is complete you will need enter a 2 digit number that tells the the partition and slot assignment the keypad your system has partitions you will to also assign the keypad to a par 1st digit slot assignment 2nd digit tells the which keypad slots are occupied panel can then generate a fault when keypad supervisory signal is not There are eight available slots keypads LCD5511 keypads are al assigned to slot 1 by default You need to assign each keypad to its slot 1 to 8 the following at each keypad in on the system Enter Installer Programming by press Code Press 000 for Keypad Programming Press 0 for Partition and Slot Assign Enter a two digit number to specify the and slot assignment If your system does not have partitions 1 for the first digit digit Enter 0 for Global Keypad 1 for Partition 1 Keypad 2 for Partition 2 Keypad 3 for Partition 3 Keypad 4 for Partition 4 Keypad 5 for Partition 5 Keypad 6 for Partition 6 Keypad 7 for Partition 7 Keypad 8 for Partition 8 Keypad digit Enter 1 to 8 for Slot Assignment Press the key twice to exit pro After assigning all keypads perform a Code 902 The pan will now supervise all assigned key and enrolled modules on the the Keypad are several programming options for the LCD5511 keypad These described below Record all your choices in the program worksheets included in this manual the LCD5511 is similar to the rest of the system you are in the LCD5511 program sections the keypad will display options are turned on along the top the display To turn an option on or off the number corresponding to the on the number pad The numbers the options that are currently turned will be displayed example if options 1 and 2 are on display will look like information on programming the rest your security system please refer to system Installation Manual Key Options function keys are programed in sec 000 1 4 By default the 4 function on the keypad are programmed as Arm 03 Away Arm 04 Chime Aux 11 You can change the func of each key on every keypad Please your system Installation Manual for on programming the keys a complete list of all the function key available for your system Options LCD5511 will display the current after 4 seconds of no key presses set the correct time and date for the please refer to your system In Manual You can change how keypad displays the time with the fol options To change the clock op Enter code Enter 000 to go to keypad program Enter section 6 to go to clock op To turn any of the options on or off 1 2 or 3 If the Time does not display on keypad is selected make sure that the Keypad time when zones are open option is selected ON Time displays on keypad Time does not display on ON Clock display is in 12 hour e g 08 00 Clock display is in 24 hour e g 20 00 ON Keypad does not display time zones are open Keypad displays time when are open When you are finished programming clock options press to exit Displayed While Armed Option can disable the display of alarms on keypad when the system is armed display of alarms is enabled by de To disable the display of alarms the system is armed turn off sec 6 option 5 Enter code Enter 000 to go to keypad program To turn the display of alarms on or off section 6 Turn option 5 on or off cid 9 cid 10 Alarms not displayed system is armed Alarms are always dis while system is armed When you are finished press to exit Key Options Fire Auxiliary can enable or disable the Fire Auxil and Panic keys at each keypad keys are enabled by default see your system Installation