DSC MD12 Installation Manual (English, French)

MD12 Modem INSTRUCTIONS v1.1 DSC modem is a communication device designed to enable computer terminals of an RS 232 port communicate via telephone lines with the DSC line of downloadable systems The modem is compatible with the DSC proprietary formats 110 Baud 300 and 625 Baud Lights LED indicators on the top of the modem indicate the following ON Red Data to control panel TX Green Data from control panel RX Red to the Computer not apply power until all connections are made and verified An improper connection may your computer or modem For Finland Norway and Sweden the computer used must be an Approved Class II powered via a CEE 7 16 AC outlet for other countries the computer must be con to a AC outlet with a protective earth ground connection The outlet of the MD12 trans must be positioned near the equipment and be easily accessible MD12 provides computer interface via a standard DB25 female connector Use a DB25 serial to connect the MD12 to the computer serial port to a Telephone Line the modem there are two 4 pin connections The 4 pin connector marked is for an telephone The connector marked is for the incoming telephone line from the wall When the modem is in communication the optional telephone connection will be auto disconnected for the duration of the communication Settings selects the pulse dialling option ON North America OFF Europe DSC Modem 230 VAC 50Hz to 12 VAC 1A Power Supply Europe or 120 VAC 60Hz to 12 VAC 1A Power Supply North America 4 pin telephone cable Rate 110 300 and 625 bps 8 data bits no parity 1 stop bit Requirements 12 VAC 150mA Touch Tone Dialling DTMF or Pulse Dialling Temperature 0 40 32 110 MD12 is compatible with DLS 1 V6.2 and higher DLS 2 V1.30 and all other DSC DLS Windows downloading software packages Refer to the DLS Manual Help for modem communication instructions and computer configuration requirements Dialling Commands dialling modifier commands shown below may be programmed into the phone number to set dialling functions Modifier of Function for Additional Dial Tone Notes for New Zealand PTC200 General Warning The grant of a Telepermit for any item of terminal equipment indi only that Telecom has accepted that the item complies with minimum conditions for con to its network It indicates no endorsement of the product by Telecom nor does it any sort of warranty Above all it provides no assurance that any item will work cor in all respects with another item of Telepermitted equipment of a different make or model does it imply that any product is compatible with all of Telecom network services PTC200 8.1.3 2 8.1.4 b 8.2.1 Automatic Call Setup Some parameters required for with Telecom Telepermit requirements are dependent on the equipment PC with this device The associated equipment shall be set to operate within the follow limits for compliance with Telecom Specifications There shall be no more than 10 call attempts to the same number within any 30 minute for any single manual call initiation and The equipment shall go on hook for a period of not less than 30 seconds between the end of attempt and the beginning of the next call attempt Automatic calls to different numbers are spaced such that there is not less than 5 seconds the end of one call attempt and the beginning of another PTC200 8.1.7 b User Instructions automatic call set up This equipment shall not be up to make automatic calls to Telecom 111 Emergency Service PTC200 7.5.1 General operation ringer sensitivity and loading This device only to Distinctive Alert cadence s DA1 and DA2 Installation The register S7 Wait for carrier after answer default value shall be set to 90 seconds For connections to the telephone sockets use only approved telephone cables that terminate a type of plug adapter from RJ11 to BS6312 is required for MD12 license agreement the separation between the equipment and receiver Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end user license agreement is licensed to You under the terms of This End User License Agreement is a legal agreement between You the company individual or entity who acquired the Software and any related and Digital Security Controls a division of Tyco Safety Products Canada Ltd the manufacturer of the integrated security systems and the of the software and any related products or components which You acquired the DSC software product PRODUCT or is intended to be accompanied by HARDWARE and is NOT accompanied by new You may not use copy or install the SOFTWARE PRODUCT The SOFTWARE PRODUCT includes computer software and may include asso media printed materials and or electronic documentation The MD12 Modem is intended to be installed and operated by service persons only or equivalent i e persons having appropriate technical training and the experience necessary to be of hazards to which that person may be exposed in performing a task and of measures to minimize the risks to that person or other persons This equipment is intended for temporary con to a telecommunication network during the course of installation maintenance or repair of DSC systems that are connected to a telecommunication network Never install the equipment telephone wiring during a lightning storm Make sure the cables are laid in such a way that accidents cannot occur connected cables must not be subject to excessive mechanical strain manual shall be used with the Installation Manual of the alarm control panel All the instructions specified within that manual must be observed Warranty Security Controls warrants that for a period of twelve months from the date of purchase the product shall be free of defects in materials workmanship under normal use and that in fulfilment of any breach of such warranty Digital Security Controls shall at its option repair or the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in parts and workmanship not to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Security Controls such as lightning voltage mechanical shock water damage or damage arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether expressed or and of all other obligations or liabilities on the part of Digital Security Controls Digital Security Controls neither assumes responsibility nor authorizes any other person purporting to act on its behalf to modify or to change this warranty nor to assume for it any other warranty or concerning this product In no event shall Digital Security Controls be liable for any direct indirect or consequential damages loss of profits loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure of this Important Information Changes or modifications not expressly approved by Digital Security Controls could void the user to operate this equipment Compliance Statement Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These lim are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio commu There is no guarantee that interference will not occur in a particular installatio