DSC PC1150 - User Manual - English - ClassicSeries 4 Zone Alarm Control Panel

INSTRUCTION R0 22 1993 Warranty Security Controls Ltd warrants that for a period of twelve months from the date of purchase the shall be free of defects in material and workmanship under normal use and that in fulfilment of breach of such warranty Digital Security Controls Ltd shall at its option repair or replace the equipment upon return of the equipment to its repair depot This warranty applies only to in parts and workmanship and not to damage incurred in shipping or handling or damage due to beyond control of Digital Security Controls Ltd such as lightning excessive voltage mechanical water damage or damage arising out of abuse alteration or improper application of the foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all warranties whether express or implied and of all other obligations or liabilities on the part of Digital Controls Ltd This warranty contains the entire warranty Digital Security Controls Ltd neither nor authorizes any other person purporting to act on its behalf to modify or to change this nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages of anticipated profits loss of time or any other losses incurred by the buyer in connection with the installation or operation or failure of this product Security Controls Ltd recommends that the entire system be completely tested on regular basis However despite frequent testing and due to but not limited to criminal or electrical disruption it is possible for this product to fail to perform as COMPLIANCE Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to use this equipment equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to to correct the interference by one or more of the following measures Re orient the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio television technician for help user may find the following booklet prepared by the FCC useful to Identify and Resolve Radio Television Interference Problems This is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 INFORMATION equipment complies with Part 68 of the FCC Rules On the side of this equipment is a label that contains among other information the FCC number of this equipment to Telephone Company request the customer shall notify the telephone company of the particular line to which the connection will be made and provide the FCC number and the ringer equivalence of the protective circuit Registration Number Registration Number FCC Registration Number Registration Number F53CAN 73151 AL E Registration Number Equivalence Number Equivalence Number Equivalence Number 0.1B Equivalence Number Equivalence Number Jack Jack Jack RJ 31X Jack Jack Connection Requirements for the telephone company provided ringers all connections to the telephone network shall be made through standard plugs and company provided jacks or equivalent in such a manner as to allow for easy immediate disconnection of the terminal equipment jacks shall be so arranged that if the plug connected thereto is withdrawn no interference to the operation of the equipment at the premises which remains connected to the telephone network shall occur by reason of such withdrawal Ensure that plugs and jacks the dimension tolerance and metallic plating requirements of 47 C F R Part 68 Subpart F of Harm terminal equipment or protective circuitry cause harm to the telephone network the telephone company shall where practicable notify customer that temporary disconnection of service may be required however where prior notice is not practicable the telephone company temporarily discontinue service if such action is deemed reasonable in the circumstances In the case of such temporary discontinuance telephone company shall promptly notify the customer and will be given the opportunity to correct the situation Telephone Company Information security control panel must be properly connected to the telephone line with a USOC RJ 31X telephone jack FCC prohibits customer provided terminal equipment be connected to party lines or to be used in conjunction with coin telephone service rules may vary from state to state in Telephone Company Equipment of Facilities telephone company may make changes in its communications facilities equipment operations or procedures where such actions are required and proper in its business Should any such changes render the customer terminal equipment incompatible with the company facilities the customer shall be given adequate notice to the effect modifications to maintain uninterrupted service Equivalence Number REN REN is useful to determine the quantity of devices that you may connect to your telephone line and still have all of those devices ring when telephone number is called In most but not all areas the sum of the RENs of all devices connected to one line should not exceed five 5.0 be certain of the number of devices that you may connect to your line you may want to contact your local telephone company Maintenance Facility you experience trouble with this telephone equipment please contact the facility indicated below for information on obtaining service or repairs not return equipment to this address without prior authorization The telephone company may ask that you disconnect this equipment from network until the problem has been corrected or until you are sure that the equipment is not malfunctioning Security Controls Ltd Washburn Street NY 14094 Zones are three zones that can be activated from the keypad by pressing and holding two keys at the time These keys are only functional if they have been programmed by your installer The installer indicate which of these keys are functional and the functional keys should be noted on the Information page in this manual Holding these keys down for two seconds will sound a Pulsed Alarm The siren will sound in a mode The keypad will sound three beeps once the system has accepted the alarm An auxiliary device is also activated if your installer has connected it to your system To silence the alarm enter Access Code Holding this key down for two seconds activates a silent alarm if your installer has this option When activated there is no audible alarm and no lights on the keypad will on When the system has accepted the alarm the keypad will sound a series of beeps An warning device is activated only if connected to your system by your installer Holding this key down for two seconds will produce a steady tone on your siren if your installer programmed this key for audible operation An auxiliary warning device is also activated if your has connected it to your system Enter an Access Code to silence the alarm Your System is recommended that you test your system weekly Perform system tests in the off peak hours such as early morning or late evening Inform the monitoring station that you are testing your system Disarm the system light ON Perform a siren battery test by pressing Code 8 The signal will sound for about 2 If a trouble occurs after the test press to view the trouble condition Activate each sensor in turn for example open a door or window or walk in motion detector areas the Zone Lights come ON as each zone is activated The Zone Lights will go OFF when the restores to normal i e door or window closed If they are programmed for operation activate the 1 3 4 6 and functions 1 3 will the siren in a pulsed mode Enter the Access Code to silence the alarm 4 6 key is silent the may be programmed as silent or audible I