DSC PC1616 1832 1864USER MANUAL

WARNING This manual contains information on limitations regarding use and function and information on the limitations as to liability of manufacturer The entire manual should be carefully read v4.2 Manual Zealand Telecom Network following is a list of warnings applicable when this equipment is connected to the New Zealand Telecom Network Warning grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item com with minimum conditions for connection to its network It indicates no endorsement of the product by Telecom nor it provide any sort of warranty Above all it provides no assurance that any item will work correctly in all respects with item of Telepermitted equipment of a different make or model nor does it imply that any product is compatible all of Telecom network services Numbering decadic signalling signalling should not be used as it is being progressively phased out of the network DTMF dialling is 100 avail and it should always be used Grabbing Equipment equipment is set up to carry out test calls at pre determined times Such test calls will interrupt any other calls that be set up on the line at the same time The timing set for such test calls should be discussed with the installer The tim set for test calls from this equipment may be subject to If this proves to be inconvenient and your calls are inter then the problem of timing should be discussed with the equipment installer The matter should NOT be reported a fault to Telecom Faults Service Line Feed to Other Devices dialling this device unit does not provide DC voltage to the series port connection and this may cause loss of mem functions for the terminal devices local telephone connected to T 1 R 1 Operation Ringer Sensitivity and Loading device only responds to Distinctive Alert cadences DA1 and DA2 of Contents System Keypads 1 Display Symbols 2 Your Security System 3 Detection 3 3 3 3 System Operation 3 Language Selection 4 Disarming the System 4 Turning On Setting 4 Arming Turned On Set 4 Exit 4 Sounds After Away Arming 4 Turning Off Unsetting 5 Arming Partially Turning On Part Setting 5 Arming 5 Exit Delay 5 Arming and Disarming 5 Keys 5 Alarm Sounds 6 Burglar Alarm Continuous Siren 6 Alarm Pulsed Siren 6 Date Programming 6 Zones 6 Conditions 8 Menu Acknowledgement 8 Memory 8 Chime Entry Exit Beeps 8 Code Programming 8 Codes 9 Code Attributes 9 Squawk Attribute 10 Assignment Mask 10 an Access Code 10 Function Commands 10 Brightness Contrast 12 the Buzzer Level 12 the Event Buffer from a PK5500 LCD5500 Keypad 12 Global Status Screen 13 Reset 13 Sheets 13 Information 13 Codes 14 Zone Information 15 Your System 16 Your Keypad Sounder and Siren 16 Your Entire System 16 Test Mode 16 Computer Access To Your System 16 for Locating Smoke Detectors 17 Fire Safety Audit 18 Escape Planning 18 Your Security System DSC Security System has been designed to provide you with the greatest possible flexibility and Read this manual carefully and have your installer instruct you on your system opera and on which features have been implemented in your system All users of this system should be instructed in its use Fill out the Information page with all of your zone information access codes and store this manual in a safe place for future reference The PowerSeries security system includes specific false alarm reduction features and is in accordance with ANSI SIA CP 01 2000 Control Panel Standard Features for False Reduction Please consult your installer for further information regarding the false alarm features built into your system as all are not covered in this manual Detection equipment is capable of monitoring fire detection devices such as smoke detectors and provid a warning if a fire condition is detected Good fire detection depends on having adequate num of detectors placed in appropriate locations This equipment should be installed in accordance NFPA 72 N F P A Batterymarch Park Quincey MA 02269 Carefully review the Family Escape guidelines in this manual Your installer must enable the fire detection portion of this equipment before it becomes insure that your system continues to function as intended you must test your system weekly refer to the your Syste