DSC PC2550 v1 3 - Installation Manual - English - ClassicSeries 8 Zone Alarm Control Panel

INSTALLATION 1.3 The Canadian Department of Communications label identifies certified equipment This certification means that the equipment meets certain telecommunications network operational and safety requirements The Department does not guarantee the equipment will operate to the user satisfaction installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed an acceptable method of connection In some cases the company inside wiring associated with a single line individual service may be extended by means of certified connector telephone extension cord The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or malfunctions may give the telecommunications company cause to request the user to disconnect the equipment should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected This precaution may be particularly important in rural areas Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100 Load Number of this device is 42 L du minist des Communications du Canada identifie le mat homologu Cette certifie que le mat est conforme certaines normes de protection et de s des r de t Le Minist n toutefois pas que le mat fonctionnera la satisfaction de l d ce mat l doit s qu est permis de le raccorder aux installations de l locale de t Le mat doit install en une m accept de raccordement Dans certains cas les fils int de l utilis pour un service individuel a ligne unique peuvent prolong au moyen d homologu de rassordement cordon prolongateur t interne L ne doit pas oublier qu est possible que la conformit aux conditions ci dessus pas la d du service dans certaines situations Actuellement les entreprises de t ne permettent pas que l raccorde leur mat a des jacks sauf dans les cas pr pr par les tarrifs particuliers de ces entreprises r de mat homologu doivent etre effectu par un centre d canadien autoris d par le fournisseur La compagnie de t peut demander de d un appareil la suite de r ou de modifications effectu par l ou cause de mauvais fonctionnement sa propre protection l doit s que tous les fils de mise la terre de la source d des lignes t et des canalisations d m s y a sont raccord ensemble Cette pr est particuli importante dans les r rurales L ne doit pas tenter de faire ces raccordements lui meme il doit avoir recours a un service d des installations ou a electricien selon cas de charge IC assign a chaque dispositif terminal indique pour toute surcharge le pourcentage de la charge totale qui peut etre raccord a un circuit t boucl par ce dispositif La terminaison du circuit boucl peut etre constitu de n quelle combinaison de dispositifs pourvu que la somme des indices de charge de l des ne d pas 100 de charge de cet dispositif est 42 Warranty Security Controls Ltd warrants that for a period of twelve months from the date of purchase the product shall be free defects in materials and workmanship under normal use and that in fulfillment of any breach of such warranty Digital Controls Ltd shall at its option repair or replace the defective equipment upon return of the equipment to its repair This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling or due to causes beyond the control of Digital Security Controls Ltd such as lightning excessive voltage mechanical water damage or damage arising out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd This warranty contains entire warranty Digital Security Controls Ltd neither assumes nor authorizes any other person purporting to act on its to modify or to change this warranty nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct indirect or consequential damages loss of anticipated loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or of this product Digital Security Controls Ltd recommends that the entire system be completely tested on a regular However despite frequent testing and due to but not limited to criminal tampering or electrical disruption is possible for this product to fail to perform as expected OF CONTENTS 1 2 3 Testing 3 Panel 3 Procedure 3 Connections 4 for Smoke Detector Location 6 Functions 7 7 Code 7 Master Code 7 Programming Code 7 7 7 Arming 7 or Bypassing Code 7 8 Display 8 Memory Display Auxiliary Supply Control Down 4 9 Code 9 Programming Commands Code 9 Functions Command Code 0 10 Test the Clock Code 1 10 Code 2 10 Time of Day Code 4 10 Arm Code 5 10 Enable Code 6 10 Chime Test Code 8 10 Code 9 10 Callup or Output Command Code 11 Code 11 Programming Commands Home Arming