DSC PC5008 - User Manual - English

About Your Security System DSC security equipment has been designed to provide you with the greatest possible flexibility convenience Read this manual carefully and have your installer instruct you on your system and on which features have been implemented in your system All users of this system be equally instructed in its use Fill out the Information page with all of your zone and access codes and store this manual in a safe place for future reference Detection equipment is capable of monitoring fire detection devices such as smoke detectors and providing warning if a fire condition is detected Good fire detection depends on having adequate number of placed in appropriate locations This equipment should be installed in accordance with standard 74 N F P A Batterymarch Park Quincey MA 02269 Carefully review the Family Planning guidelines in this manual Your installer must enable the fire detection portion of this equipment before it will work insure that your system continues to work as intended you must test your system weekly Please to Your System on page 13 of this manual If your system does not work properly call installing company for service system is capable of sending alarms troubles and emergency information over telephone lines to monitoring station If you inadvertently initiate an alarm immediately call the monitoring station to an unnecessary response Your installer must enable the monitoring feature before it will work System Operation security system is made up of a DSC control panel one or more keypads and various sensors detectors The control panel will be mounted out of the way in a utility closet or in a basement The cabinet contains the system electronics fuses and stand by battery There is normally no reason anyone but the installer or service professional to have access to the control panel the keypads have an audible indicator and command entry keys The LED keypads have a group zone and system status lights The LCD keypad has an alphanumeric liquid crystal display LCD keypad is used to send commands to the system and to display the current system status The will be mounted in a convenient location inside the protected premises close to the entry door s security system has several protected areas zones and each of these will be connected to one more sensors motion detectors glassbreak detectors door contacts etc A sensor in alarm will indicated by the corresponding zone lights flashing on an LED keypad or by written messages on LCD keypad NOTICE security system cannot prevent emergencies It is only intended to alert you and if included monitoring station of an emergency situation Security systems are generally very reliable they may not work under all conditions and they are not a substitute for prudent security or life and property insurance Your security system should be installed and serviced by security professionals who should instruct you on the level of protection that has been and on system operations Information Codes out the following information for future reference and store this manual in a safe place Master Code is Access Codes 09 10 11 12 13 14 15 16 25 26 27 28 29 30 31 32 Information Area Type Zone F FIRE Zone A AUXILIARY Zone P PANIC Exit Delay Time is seconds Entry Delay Time is seconds Service Station Information Information Codes Codes are used to arm and disarm the system There are 33 access codes available one Code and 32 access codes the Master Code can be used to program additional security codes and to change other system as well as to arm and disarm the security system Your installer will supply the Master Code to All keypad entries are made by pressing one key at a time will be able to program all access codes by following the procedure outlined in Codes on page 6 An access code can be a four or six digit number depending on how your installer has your system Ask your installer for more information regarding access codes the System from an LED Keypad the Ready light is ON the system is ready to be armed If the Ready light is OFF check to see that doors and windows are closed and that motion is stopped in areas covered by motion detectors system cannot be armed unless the Ready light is ON indicating that all zones are closed and the is in the Ready state your access code As each digit is entered the keypad sounder will beep If the access code entered incorrectly the keypad buzzer will sound steadily for one second If this occurs re enter access code correctly If the correct access code is entered the keypad sounder will beep and the Armed light will come ON Exit the premises through the door indicated by your as the Exit Entry door panel will provide an exit delay period indicated by keypad beeps for you to exit the premises causing an alarm At the end of the exit delay period all keypad lights except the Armed light turn OFF and the system will be armed Your installer can change the exit delay time from an LCD Keypad of the following messages may appear when you attempt to arm your system System Arming Code to System or more zones are not secured To secure the system close all doors and and cease all motion in areas covered by motion detectors the arrow keys to verify that the system is clear of troubles and that no are bypassed unintentionally see Trouble Conditions on page 11 Bypassing on page 10 System Enter Code you see this message your installer has set up your system so that it may be with one or more designated zones open Ask your installer for more details system is in the Ready state and may be fully armed To arm the system enter access code Code to System the correct access code has been entered the display will be Delay in Code to System WARNING Active panel will provide an exit delay period also indicated by keypad beeps for you exit the premises without causing an alarm Exit through the door indicated by installer as the Exit Entry door message will be displayed once the exit delay expires and the system is fully this message appears be aware of which zones are bypassed and why see Bypassing on page 10 NOTE If you arm the system with a zone or with a trouble present your security protection is reduced Arming Methods Arming the system in the Away mode will have all interior zones and perimeter zones active If motion detected in the interior zones or if one of the perimeter zones is violated the alarm sequence will To arm in the Away mode enter your access code or press the Away button on the keypad exit the premises through a designated Exit Entry door The system will recognize that occupants left the premises Once the exit delay expires the system will be fully armed Exit Fault an attempt to reduce false alarms the Audible Exit Fault will to notify you of an improper exit when the system in the Away mo