DSC PC5132-433 v4 2 - Installation Manual - English - PowerSeries Wireless Receiver

W A R N I N G cid 127 manual contains information on limitations regarding use and function and information on the limitations as to of the manufacturer NA 4.2 COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the instructions may cause interference to radio and television reception It has been type tested and found to comply with limits for Class B device in accordance with the specifications in Subpart of Part 15 of FCC Rules which are designed to reasonable protection against such interference in any residential installation However there is no guarantee that interference not occur in a particular installation If this equipment does cause interference to television or radio reception which can be by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may the following booklet prepared by the FCC helpful to Identify and Resolve Radio Television Interference Problems This is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 Class B digital apparatus meets all requirements of the Canadian interference causing equipment regulations appareil num de la Classe B respecte toutes les exigences de r sur le mat brouilleur du Canada L de l Canada identifie le mat Cette certifie que le mat est conforme normes de protection d et de s des de t Industrie Canada n toutefois que le mat fonctionnera la satisfaction de l d ce mat l doit s qu est de le raccorder aux installations de l locale de Le mat doit install en une m accept de raccordement L ne doit pas qu est possible que la conformit aux conditions n pas la d du service dans certaines r de mat homologu doivent effectu par un d canadien autoris d par le fournisseur La de t peut demander l de un appareil la suite de r ou de modifications par l ou cause de mauvais fonctionnement sa propre protection l doit s que tous les fils mise la terre de la source d les lignes et les canalisations d m s y en a sont ensemble Cette pr est particuli importante les r rurales L ne doit pas tenter de faire ces lui m il doit avoir recours un service d installations ou un selon le cas de charge IC assign a chaque dispositif terminal indique toute surcharge le pourcentage de la charge totale qui raccord un circuit t boucl utilis par ce La terminaison du circuit boucl peut constitu de quelle combinaison de dispositifs pourvu que la somme indices de charge de l des dispositifs ne d pas de charge de ce produit est 2 The Industry Canada label identifies certified equipment certification means that the equipment meets certain telecom network protective operational and safety require Industry Canada does not guarantee the equipment will to the user satisfaction installing this equipment users should ensure that it is to be connected to the facilities of the local telecommu company The equipment must also be installed using an method of connection The customer should be aware compliance with the above conditions may not prevent degra of service in some situations to certified equipment should be made by an authorized maintenance facility designated by the supplier Any or alterations made by the user to this equipment or malfunctions may give the telecommunications com cause to request the user to disconnect the equipment should ensure for their own protection that the electrical connections of the power utility telephone lines and metallic water pipe system if present are connected This precaution may be particularly important in rural Users should not attempt to make such connections but should contact the appropriate electric inspection or electrician as appropriate Load Number LN assigned to each terminal device denotes percentage of the total load to be connected to a telephone loop is used by the device to prevent overloading The termination a loop may consist of any combination of devices subject only the requirement that the total of the Load Numbers of all the does not exceed 100 Load Number of this unit is 2 of Contents How to Use this Manual 1 Specifications and Features 1 Compatible Wireless Devices 2 Batteries 2 Set up Wiring Unpack the PC5132 3 Choose a Mounting Location for the PC5132 3 Antennas 3 Connect the PC5132 433 Receiver 3 Wireless Devices A Note about Electronic Serial Numbers 4 Enrolling Wireless Devices 4 Enroll Program Wireless Keys WLS9X9 433 4 Wireless Keys 6 Programming Program Zones and Partitions 7 Enable PC5132 433 Supervision 7 Enable Supervision of Wireless Zones 8 Signal Detection 8 PC5132 433 Software Default 9 Deleting Wireless Devices 9 Mounting the Reception of Wireless Devices 10 Mount the PC5132 433 and Wireless Devices 12 Notes Conditions 13 Signal Detection 13 Wireless Zone Low Battery Transmission 13 Worksheets for Locating Smoke Detectors you for purchasing the PC5132 433 Wireless Receiver This product the result of several years of development and will allow you to connect to 32 wireless detection devices to the PC580 P