DSC PC5200 v2 0 IS EN NA

File Preview
File Preview
Click below to download for free

File Data

Name dsc-pc5200-v2-0-is-en-na-3129875640.pdf
Type PDF
Size 777.25 KB
Downloads

Text Preview

Keybus The 4 wire Keybus connection is used by the panel to communicate with module Connect the RED BLK YEL and GRN terminals to the RED BLK YEL GRN Keybus terminals on the PC5020 control panel Jumper Settings PC5200 has 2 jumpers to select which PC5200 slot is to be used refer to table below 2 1 2 3 4 Warranty Security Controls Ltd warrants that for a period of 12 months from the date of purchase the product be free of defects in materials and workmanship under normal use and that in fulfilment of any breach of warranty Digital Security Controls Ltd shall at its option repair or replace the defective equipment return of the equipment to its factory This warranty applies only to defects in parts and workmanship not to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Controls Ltd such as lightning excessive voltage mechanical shock water damage or damage out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Ltd This warranty contains the entire warranty Digital Security Controls Ltd neither assumes for nor authorizes any other person purporting to act on its behalf to modify or to change this nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct or indirect or consequential damages loss anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase or operation or failure of this product Digital Security Controls Ltd recommends that the entire system be completely tested on a basis However despite frequent testing and due to but not limited to criminal tampering or electrical it is possible for this product to fail to perform as expected COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could your authority to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the instructions may cause interference to radio and television reception It has been type tested and found to comply the limits for Class B device in accordance with the specifications in Subpart cid 147 B cid 148 of Part 15 of FCC Rules which are designed provide reasonable protection against such interference in any residential installation However there is no guarantee that will not occur in a particular installation If this equipment does cause interference to television or radio reception can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user find the following booklet prepared by the FCC useful cid 147 How to Identify and Resolve Radio Television Interference This booklet is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 Digital Security Controls Ltd Canada www dsc com Support 1 800 387 3630 in Canada 29005251 R004 all comments concerning this to pubs dscltd com Instructions PC5200 can be used to provide up to 1.0A of additional current to the PC5020 panel see PC5020 Installation Manual for complete installation instructions PC5020 v3.1 or higher supports up to four PC5200 modules 1 eriF eriF eriF eriF eriF eriF eriF eriF Panel PC5020 Descriptions Devices that require from the PC5200 shall UL Listed for the intended and operate over range 11.5 12.5VDC battery requirements and time refer to Table 1 Battery model BD7 12 37VA FTC Frost 40VA PTD 1640 Supervised the PC5200 requires a 16.5V 37VA or 16V 40VA transformer primary of the transformer to an unswitched AC source maximum current 0.5A and connect the secondary of the transformer to these terminals This terminal is used to provide power for expansion modules devices refer to Table 1 for maximum rating This can be used to tamper the cabinet in which the PC5200 is mounted a normally closed NC switch across TAM and BLK If the tamper is not being connect a piece of wire across TAM and BLK to secure the tamper this a trouble condition from occurring v2 O Supply Module The 4 wire Keybus connection is used by the panel to communicate with module Connect the RED BLK YEL and GRN terminals to the RED BLK YEL GRN Keybus terminals on the PC5020 control panel Jumper Settings PC5200 has 2 jumpers to select which PC5200 slot is to be used refer to table below 2 1 2 3 4 Warranty Security Controls Ltd warrants that for a period of 12 months from the date of purchase the product be free of defects in materials and workmanship under normal use and that in fulfilment of any breach of warranty Digital Security Controls Ltd shall at its option repair or replace the defective equipment return of the equipment to its factory This warranty applies only to defects in parts and workmanship not to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Controls Ltd such as lightning excessive voltage mechanical shock water damage or damage out of abuse alteration or improper application of the equipment foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Ltd This warranty contains the entire warranty Digital Security Controls Ltd neither assumes for nor authorizes any other person purporting to act on its behalf to modify or to change this nor to assume for it any other warranty or liability concerning this product no event shall Digital Security Controls Ltd be liable for any direct or indirect or consequential damages loss anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase or operation or failure of this product Digital Security Controls Ltd recommends that the entire system be completely tested on a basis However despite frequent testing and due to but not limited to criminal tampering or electrical it is possible for this product to fail to perform as expected COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to use this equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the manufacturer cid 146 s may cause interference to radio and television reception It has been type tested and found to comply with the limits for Class B in accordance with the specifications in Subpart cid 147 B cid 148 of Part 15 of FCC Rules which are designed to provide reason

Related Files