DSC PC5401 v1 0 - Installation Manual - English - PowerSeries RS-232 Automation Interface Module

File Preview
File Preview
Click below to download for free

Text Preview

Table 1 BAUD Selection selection can only be changed by cycling power to the module 2 Indicator LEDs Link Status 2 seconds the module is correctly connected to KEYBUS Flashes every 2 seconds when module is normally A solid RED means that module is not operating properly If the is unlit the module is not powered check cabling Warranty Security Controls warrants that for a period of twelve months from the date of purchase the product shall be free of defects in and workmanship under normal use and that in fulfillment of any breach of such warranty Digital Security Controls shall at its repair or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in and workmanship and not to damage incurred in shipping or handling or damage due to causes beyond control of Digital Security such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper of the equipment The foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether express or implied and of all other obligations or liabilities on the part of Digital Security Controls This warranty the entire warranty Digital Security Controls neither assumes responsibility nor authorizes any other person purporting to act on behalf to modify or to change this warranty nor to assume for it any other warranty or liability concerning this product In no event shall Security Controls be liable for any direct indirect or consequential damages loss of anticipated profits loss of time or any other incurred by the buyer in connection with the purchase installation or operation or failure of this product DSC recommends that the entire system be completely tested on a regular basis However despite frequent testing and due but not limited to criminal tampering or electrical disruption it is possible for this product to fail to perform as expected COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the manufacturer instructions may cause to radio and television reception It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in any residential installation However there is no that interference will not occur in a particular installation If this equipment does cause interference to television or radio reception which can be determined turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet by the FCC useful to Identify and Resolve Radio Television Interference Problems This booklet is available from the U S Government Printing Washington D C 20402 Stock 004 000 00345 4 2004 Digital Security Controls Canada www dsc com Support 1 800 387 3630 in Canada Instructions PC5401 Data Interface Module can be used to quickly and easily communicate PowerSeries panels through a standard RS 232 serial connection See the Developer Guide for more information on communicating with the PC5401 at www dsc com support installation manuals Current Draw 35 mA Connections The 4 wire KEYBUS connection is used by the panel to communicate the module Connect the RED BLK YEL and GRN terminals to the KEYBUS on a PowerSeries panel Requires a RS 232 cable Only the RX TX and GND are used Note cable should not exceed 50 ft at 9600 BAUD consult Signaling Standard for more information Connect Module to a Control Panel module can be installed in any of the following enclosures PC4003C HS CAB1000 HS CAB3000 HS CAB4000 Connect module to the KEYBUS with the panel powered down Select desired BAUD using JP1 3 default is 9600 BAUD see Table 1 Connect an RS 232 cable to the application Power up the system 1 BLK YEL GRN Application Panel The PC5401 is designed to be installed by SERVICE PERSONS only These instructions shall be used in conjunction with the applicable Instructions of the used PowerSeries alarm controller Interface Module 1 O 1 BAUD Selection selection can only be changed by cycling power to the module 2 Indicator LEDs Link Status 2 seconds the module is correctly connected to KEYBUS Flashes every 2 seconds when module is normally A solid RED means that module is not operating properly If the is unlit the module is not powered check cabling Warranty Security Controls warrants that for a period of twelve months from the date of purchase the product shall be free of defects in and workmanship under normal use and that in fulfillment of any breach of such warranty Digital Security Controls shall at its repair or replace the defective equipment upon return of the equipment to its repair depot This warranty applies only to defects in and workmanship and not to damage incurred in shipping or handling or damage due to causes beyond control of Digital Security such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper of the equipment The foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other whether express or implied and of all other obligations or liabilities on the part of Digital Security Controls This warranty the entire warranty Digital Security Controls neither assumes responsibility nor authorizes any other person purporting to act on behalf to modify or to change this warranty nor to assume for it any other warranty or liability concerning this product In no event shall Security Controls be liable for any direct indirect or consequential damages loss of anticipated profits loss of time or any other incurred by the buyer in connection with the purchase installation or operation or failure of this product DSC recommends that the entire system be completely tested on a regular basis However despite frequent testing and due but not limited to criminal tampering or electrical disruption it is possible for this product to fail to perform as expected COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to use this equipment equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the manufacturer instructions may cause to radio and television reception It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in any residential installation However there is no that interference will not occur in a particular installation If this equipment does cause interference to television or radio reception which can be determined turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient the receiving antenna Reloc

Related Files